Chapin 22251XP - Manual

WARNING
2. Pre-Use Check
3. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
7. Care, Storage and Maintenance
010522-20 (A) R0412
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known to the State of
California to cause birth defects and other reproductive harm. Wash hands after handling.
6-6136
Hose
Manguera
Tuyau
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-4602
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
1. Hose to Tank
Discharge/ Assembly
• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).
• Proper placement of white outlet tube (Fig. 1C).
• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab
with notches on the tank adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).
Discharge
Assembly
1B
Outlet
Tube
1E
Retaining Nut -
Securely tightened.
1C 1D No
Gap
Tank
Adapter
Outlet Tube
Adapter
Tab/
Notch
1A
Outlet Tube
Adapter
Outlet
Tube
Parts, Piezas, Pièces
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse
suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior
of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank
weakening and could result in explosive bursting under pressure. If any of these signs are found, discard
tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20
strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and
proceed with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If
any of these conditions are found, replace affected part with original manufacturer’s part before using.
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and
Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are
thoroughly rinsed with water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening
in cover.
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pres-
surized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store
or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protec-
tion when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or
body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution
from striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not
attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. This sprayer is designed
for acidic solutions only. Never spray flammable, chlorine or bleach, caustic, or other corrosive solutions
or heat, pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instruc-
tions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Sk-1159-1
8. Troubleshooting
Clean Nozzle Assembly (Fig. 7A) -Remove nozzle cap by unscrewing. Clean and re-assemble.
8A
Nozzle Cap
301892-4
Shut-off Handle
Mango de cierre
Poignée du robinet
4. Pressurizing and Spraying
Do: Turn handle clockwise
to tighten. Push handle
down, turn 1/4 turn coun-
terclockwise to release.
Do: Pump until you
feel resistance.
Do: Push handle, down, turn
1/4 turn clockwise to lock.
Begin spraying. Re-pump
sprayer as required to maintain
spray force.
4A 4C 4B
5. To Release Pressure
1) Your sprayer is equipped with a pressure relief/release
valve (Fig. 5A). To release pressure lift and hold the cap
until air is completely exhausted, OR, turn the valve
slowly counterclockwise until you hear air escaping and
wait air is completely exhausted (Fig. 5B).
2) Do: Stay away from the sprayer until all air has escaped.
5A 5B
6. Wand Dock Clip
Choose the holder that fits your wand.
6-4606
Pressure Relief Valve
Válvula de descarga de presión
Soupape de décompression