Mallory Ignition Mallory HYFIRE IV SERIES Ignition System 692_697 - Manual (Page 7)

7
MAGNETIC PICKUP/CRANK TRIGGER COLOR CODES
BRAND/TYPE
MAG+ MAG–
MALLORY CRANK TRIGGER PURPLE GREEN
MALLORY BILLET COMPETITION DISTRIBUTOR,
SERIES NOS. 81 AND 84
ORANGE PURPLE
MALLORY COMP 9000 ® SERIES NOS 96-99 ORANGE PURPLE
MALLORY HARNESS PART NO. 29040 RED BLACK
MSD™ CRANK TRIGGER PURPLE GREEN
MSD™ CRANK TRIGGER (OLD STYLE) ORANGE BLACK
MSD™ DISTRIBUTOR ORANGE PURPLE
MOROSO™ CRANK TRIGGER BLACK WHITE
ACCEL ® CRANK TRIGGER BLACK WHITE
CHRYSLER ELECTRONIC DISTRIBUTOR ORANGE BLACK
FORD DURASPARK DISTRIBUTOR ORANGE PURPLE
DELCO/GM HEI DISTRIBUTOR WHITE GREEN
2BWiring method without adapters; all breaker point distributors;
Mallory Electronic Ignitions (three wire/red, brown, green); OEM
electronic ignition amplifiers.
Refer to: Figure 14 for breaker point distributors; Figure 16 for Mallory UNILITE
®
Distributors, Magnetic Breakerless Distributors or Electronic Advance Distributors
(three wire/red, brown, green); Figure 17 for OEM electronic ignition amplifiers
Connecting the Ignition Control Harness
• Route the Ignition Control Harness to the ignition coil so that its wires do not make contact with
extreme heat, sharp objects or moving devises such as fans, belts and linkages.
• Disconnect ALL wires located on the ignition coil (+) terminal. These include the wires from the
ignition switch/ignition ballast resistor, start/ignition bypass and any other wires normally
connected to the ignition coil (+) terminal. Connect these wires to the RED WIRE. NOTE: The
RED WIRE must get voltage when the ignition switch is in the START and RUN positions. If
you are using a Mallory Electronic Ignition, connect its BROWN WIRE to engine ground and
add its RED WIRE to the Ignition Control Harness RED WIRE. Use Ring Terminal Connectors
to join wires together (See page 2 - Ignition Ballast Resistor / Loom Resistance Wire and
Standard Ignition Bypass).
• Similarly, disconnect ALL wires located on the ignition coil (–) terminal. Connect these wires to
the GREEN WIRE. If you are using a Mallory Electronic Ignition, add its GREEN WIRE to the
Ignition Control Harness GREEN WIRE. Use Ring Terminal Connectors to join wires together.
• Connect the YELLOW WIRE to the ignition coil (+) terminal. DO NOT allow any wire except
the YELLOW WIRE to make contact with the ignition coil (+) terminal.
• Connect the BLACK WIRE to the ignition coil (–) terminal.
• Go to Step 3, page 9.
RING TERMINAL CONNECTORS:
Furnished with the HYFIRE ® IV Electronic Ignition Controls are two Ring Terminal Connectors
for the convenience of getting a neat installation when the HYFIRE ® IV Electronic Ignition
Control is added to an existing ignition system. These Ring Terminal Connectors allow the
existing ignition system wiring to remain in the area of the ignition coil.
• Move wires onto the stud that is inside the Ring Terminal Connector body.
• Secure these wires to the stud with the nut and washer.
• Install the Ring Terminal Connector cap.
2CWiring Method without adapters for Magnetic Pickup Trigger
Pulses (Non-Computer Type); Magnetic Pickup Distributors or
Crank Trigger Ignition
Connecting to Magnetic Pickup Distributors and Crank Trigger Ignition – Refer to
Figure 18.
• Connect the magnetic pickup (+) wire to the SMALL GREEN WIRE from the HYFIRE ® IV
Electronic Ignition Control.
• Connect the magnetic pickup (–) wire to the SMALL BLACK WIRE from the HYFIRE ® IV
Electronic Ignition Control.
Connecting the Ignition Control Harness:
• Route the Ignition Control Harness to the ignition coil so that its wires do not make
contact with extreme heat, sharp objects or moving devises such as fans, belts and
linkages.
• Connect the RED WIRE to the 12-volt wire from the ignition switch. NOTE: The RED
WIRE must get voltage when the ignition switch is in the START and RUN positions. Use
a Ring Terminal Connector to join wires together.
• Connect the YELLOW WIRE to the ignition coil (+) terminal. DO NOT allow any wire
except the YELLOW WIRE to make contact with the ignition coil (+) terminal.
• Connect the BLACK WIRE to the ignition coil (–) terminal.
• DO NOT connect the GREEN WIRE of the Ignition Control Harness to anything. Tape
the end of it to insulate it.
• Go to Step 3, Page 9.
FIGURE 10