11 call waiting, 10 hang up tone number, 9 answer incoming call on x rings – DoorKing 1812 Access Plus User Manual
Page 36: Factory setting is 1 (call waiting on), Factory setting is 0, Factory setting is 06 (6 rings)
1812-162-M-1-12
34
2.4.11 Call Waiting
Factory setting is 1 (Call Waiting On).
These steps will turn the Call Waiting feature either ON or OFF. The call waiting feature will allow the resident to place an
outside call on hold when a visitor presses the call button on the 1812. Once communication with the visitor is established,
access can be granted or denied. If access is granted (press the number to open the door or gate), the 1812 will automati-
cally switch the call back to the outside call. If the resident wants to deny access, they simply press the # key to switch
back to the outside call.
1. Press
*
2 0 and enter the MASTER CODE. [
*
2 0 _ _ _ _ (beep)]
2. Press 1
*
to turn Call Waiting ON OR press 0
*
to turn Call Waiting OFF. [ _
*
(beep)]
3. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
2.4.12 Turn Speaker On / Control Relay from Off-Site Call
This command allows you to call the 1812 from a remote location and turn on the speaker at the unit to enable two-way
voice communication and will allow relay control – all “Tone Open Numbers” that are programmed (2.4.8).
1. Call the resident’s phone number. After the programmed number of rings (2.4.9) the 1812 will answer
with a tone.
2. Press
*
1 6 and enter the MASTER CODE. [
*
1 6 _ _ _ _ (beep)]
If you use a “tone open number” during the call to activate a relay, the 1812 will automatically hang up
after the “tone open number” is used. Only one activation number will function per phone call.
Example: If you call and want to “Hold Open” the relay, you will have to call back to “Deactivate” it later.
3. Hang up when your conversation is completed when NOT using a “tone open number”.
2.4.10 Hang Up Tone Number
Factory setting is 0.
These steps set the number that will hang-up the 1812 after the conversation is completed. The hang up tone is used when
a call from the 1812 has been forwarded to an outside number. Once the conversation has ended, the hang up tone
number should be pressed; otherwise the 1812 will remain on the line for a period of time.
1. Press
*
1 7 and enter the MASTER CODE. [
*
1 7 _ _ _ _ (beep)]
2. Enter the hang up tone number (1-9), then press
*
. [ _
*
(beep)]
3. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
2.4.9 Answer Incoming Call on X Rings
Factory setting is 06 (6 Rings).
This programming section sets the number of rings that the 1812 will allow to pass through the system before it picks up
the call. The number of rings to answer can be set from 1 to 99 rings and must be entered as a two-digit number.
For example, if you want the 1812 to answer the call after the sixth ring, enter 0 6
*
in step 2. If you program 0 0
*
in step
2, this will prevent (disable) the 1812 from answering incoming calls to it.
Important! If more than one 1812 is connected in the system (2.4.2 set for multiple systems), the 1812 that is connected
directly to the homeowner’s phones must have the “Answer Incoming Call” set for one less ring than the other 1812 units
connected.
1. Press
*
1 8 and enter the MASTER CODE. [
*
1 8 _ _ _ _ (beep)]
2. Enter the number of rings (01-99), then press
*
. [ _ _
*
(beep)]
(enter 00 in this step to disable this feature)
3. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
77
8
9
4
5
6
0
1st 1812
5 Rings
Homeowner’s
Phone
7
8
9
4
5
6
0
4th 1812
6 Rings
7
8
9
4
5
6
1
2
3
0
1111
2222
33333333
3rd 1812
6 Rings
7
8
9
4
5
6
0
2nd 1812
6 Rings
Answering:
Machine/
Service
4 Rings
Example: