Pach and Company AeGIS 4000RTP Manual - Manual (Page 19)

Pach and Company Page 11
AeGIS 400RTP Chapter 3. Programming
52
RELAY 2
(DOOR 2) OPEN
INTERVAL
(01-90 seconds)
60-62
DELETE
INDIVIDUAL
ACCESS CODE
60 :INDEX
NUMBER 01-20
61 : INDEX
NUMBER 21-40
62 : INDEX
NUMBER 41-50
65
DELETE ALL
ACCESS CODES
INDEX 01-50
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter 52 then #, you will
hear “One Short Beep”.
Step 4 Enter door 1 open interval
value (01 – 90 seconds) then press #,
you will hear “One Short Beep”.
Step 5 Enter another Function Code
to program another parameter
hear “Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the pro-
gramming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter 60, 61, 62, then #,
you will hear “One Short Beep”.
Step 4 Enter another Function Code
to program another parameter; other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Pick up the phone and wait for a dial
tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter the Function Code 52
then press #, you will hear “One Short
Beep”.
Step 5 Enter door open interval
(01 – 90 seconds) then press #, you
will hear “One Short Beep”.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three
Short Beeps”.
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter 60, 61or 62, then
press #, you will hear “One Short
Beep”.
Step 5 Return to step 4 to delete
another group of access codes or
enter another function code to program
different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 1 Call to the AeGIS 400RTP
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Enter the Function Code 52
then press #, you will hear “One Short
Beep”.
Step 4 Enter door open interval
(01 – 90 seconds) then press #, you
will hear “One Short Beep”.
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Call to the AeGIS 400RTP
system (you must know the system’s
phone number), you will hear:“One
Short Beep”, the gate is locked.“Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the
programming mode and you will hear
“One Short Beep” or
∗∗ to hang-up
the call.
Step 4 Enter 60 or 61, or 62 then
press #, you will hear “One Short
Beep”.
Step 5 Return to step 4 to delete
another group of access codes or
enter another function code to program
different parameter or exit the program
by pressing
∗ ∗ and you will hear
“Three Short Beeps”.
Step 1 Call to the AeGIS 400RTP
system (you must know the sys tem’s
phone number), you will hear:
“One Short Beep”, the gate is
locked. “Two Short Beeps”, the gate
is unlocked.
Function Local Programming Premise Phone Remote Phone