Pach and Company AeGIS 4000RTP Manual - Manual (Page 28)

98
SELECT
INITIATING
PREMISE CALL
KEY
## or **
99
SET MEMORY
TO FACTORY
DEFAULT
ERASE THE
MEMORY AND
RESET THE
SYSTEM TO
FACTORY
DEFAULT, THE
MASTER CODE
IS ALSO RESET
TO 0000
hear “Three Short Beep”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter 98 then #, you will
hear “One Short Beep”.
Step 4 Enter 0 to use # key or 1 to
use ∗∗ ∗∗ then press #, you will hear
“One Short Beep”.
Step 5 Enter another Function Code
to program another parameter other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter 99 then #, you will
hear “Two Long Beeps”.
Step 4 Enter 0 then # to cancel and
you will hear “One shor t beep” or 1
then # to clear the system’s database
and entire configuration to factory
default and you will hear “Three short
beeps”.
Step 5 Enter another Function Code
to program another parameter
otherwise press
∗ to exit and you will
hear “Three Short Beeps”.
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter the Function Code 98
then press #, you will hear “One Short
Beep”.
Step 5 Enter
0 = to select ## or
1 = to select
∗∗
then press #, you will hear “One Short
Beep”.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
It must be done locally at the
main lobby control panel.
Step 1 Call to the AeGIS 400RTP
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Enter the Function Code 98
then press #, you will hear “One Short
Beep”.
Step 4 Enter 0 (to select ##) or 1 (to
select ∗∗) then press #, you will hear
“One Short Beep”.
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
It must be done locally at the
main lobby control panel.
Function Local Programming Premise Phone Remote Phone
Pach and Company Page 20
AeGIS 400RTP Chapter 3. Programming