Audio Design Associates Cinema Reference Mach II PTM-8150 - Manual (Page 108)

Page 107
Appendix F - Cinema Reference Mach II Hex Codes
AUDIO DESIGN ASSOCIATES DEVICE NAME:
CINEMA REF MACH II / CINEMA RAP II
GENERAL COMPLEX FEEDBACK FORMAT
0F *start byte
CHARACTER 1 ASCII Character
CHARACTER 2 ASCII Character
CHARACTER 3 ASCII Character
CHARACTER 4 ASCII Character
CHARACTER 5 ASCII Character
CHARACTER 6 ASCII Character
CHARACTER 7 ASCII Character
CHARACTER 8 ASCII Character
CHARACTER 9 ASCII Character
CHARACTER 10 ASCII Character
CHARACTER 11 ASCII Character
CHARACTER 12 ASCII Character
0 3 *system assigned number
ADDRESS
*most significant nibble is UNIT.
Least significant nibble is CARD
SLOT. Or has to match the CinRef
programmed address.
F0 *stop byte
GENERAL COMMAND FORMAT
FF *start byte
0 3 *system assigned number
ADDRESS
*most significant nibble is UNIT.
Least significant nibble is CARD
SLOT. Or has to match the CinRef
programmed address.
COMMAND HIGH BYTE
COMMAND LOW BYTE
FF
*stop byte
DSP CINEMA MODE COMMANDS 1 (commands are ignored if system is in quad mode)
RESERVED FF,03,00,01,00,04,FF *reserved for this application
RESERVED FF,03,00,01,01,05,FF *reserved for this application
RESERVED FF,03,00,01,02,06,FF *reserved for this application
RESERVED FF,03,00,01,03,07,FF *reserved for this application
RESERVED FF,03,00,01,04,08,FF *reserved for this application
RESERVED FF,03,00,01,05,09,FF *reserved for this application
RESERVED FF,03,00,01,06,0A,FF *reserved for this application
RESERVED FF,03,00,01,07,0B,FF *reserved for this application
system off FF,03,00,01,08,0C,FF DC voltage is absent within this zone
RESERVED FF,03,00,01,09,0D,FF *reserved for this application
RESERVED FF,03,00,01,0A,0E,FF *reserved for this application
RESERVED FF,03,00,01,0B,0F,FF *reserved for this application
RESERVED FF,03,00,01,0C,10,FF *reserved for this application
RESERVED FF,03,00,01,0D,11,FF *reserved for this application
RESERVED FF,03,00,01,0E,12,FF *reserved for this application
RESERVED FF,03,00,01,0F,13,FF *reserved for this application
RESERVED FF,03,00,01,10,14,FF *reserved for this application
RESERVED FF,03,00,01,11,15,FF *reserved for this application
RESERVED FF,03,00,01,12,16,FF *reserved for this application
RESERVED FF,03,00,01,13,17,FF *reserved for this application
RESERVED FF,03,00,01,14,18,FF *reserved for this application
RESERVED FF,03,00,01,15,19,FF *reserved for this application
RESERVED FF,03,00,01,16,1A,FF *reserved for this application
RESERVED FF,03,00,01,17,1B,FF *reserved for this application
RESERVED FF,03,00,01,18,1C,FF *reserved for this application
RESERVED FF,03,00,01,19,1D,FF *reserved for this application
RESERVED FF,03,00,01,1A,1E,FF *reserved for this application
RESERVED FF,03,00,01,1B,1F,FF *reserved for this application
RESERVED FF,03,00,01,1C,20,FF *reserved for this application
RESERVED FF,03,00,01,1D,21,FF *reserved for this application
RESERVED FF,03,00,01,1E,22,FF *reserved for this application
RESERVED FF,03,00,01,1F,23,FF *reserved for this application
RESERVED FF,03,00,01,20,24,FF *reserved for this application
vol - unmute & power on & noise off FF,03,00,01,21,25,FF DC voltage is present within this zone
vol - soft mute FF,03,00,01,22,26,FF
format - use auto(restart default) FF,03,00,01,23,27,FF
format - force to pcm (defaults back to auto at restart) FF,03,00,01,24,28,FF not recommended for any application
format - force to ac3 (defaults back to auto at restart) FF,03,00,01,25,29,FF not recommended for any application
format - force to dts (defaults back to auto at restart) FF,03,00,01,26,2A,FF not recommended for any application
vol - master-up @ 0.5db (feedback delayed, Optimized for 1200 Baud) FF,03,00,01,27,2B,FF
vol - master-dn @ 0.5db (feedback delayed, Optimized for 1200 Baud) FF,03,00,01,28,2C,FF
vol - master-up @ 1db (feedback delayed, Optimized for 1200 Baud) FF,03,00,01,29,2D,FF
vol - master-dn @ 1db (feedback delayed, Optimized for 1200 Baud) FF,03,00,01,2A,2E,FF
remote - setup enter/execute FF,03,00,01,2B,2F,FF
remote - setup previous step FF,03,00,01,2C,30,FF
remote - setup next step FF,03,00,01,2D,31,FF
noise - sequence FF,03,00,01,2E,32,FF
noise - advance FF,03,00,01,2F,33,FF
noise - left FF,03,00,01,30,34,FF
noise - rght FF,03,00,01,31,35,FF
noise - lsur FF,03,00,01,32,36,FF
noise - rsur FF,03,00,01,33,37,FF
noise - cntr FF,03,00,01,34,38,FF
noise - lcs FF,03,00,01,35,39,FF
noise - rcs FF,03,00,01,36,3A,FF