AMX Mio R-3 - Manual (Page 2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
5/11
©2011 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-0148-03 REV: D
2. Holding the device in both hands, place your thumbs on the battery door
and slide the battery door free. The battery door should slide toward the
bottom end of the device.
3. Connect the terminal end of the Lithium-Ion battery to the port as shown
in FIG. 3. It may be necessary to use a thin, blunt non-conductive object
to seat the battery connector fully within its port.
Battery Low Indicator
When the battery charge level is too low to sustain continuous operation, the
LCD flashes "Battery Low" and the device shuts down.
Setup Mode
The Setup mode allows you to set the following device features.
Entering Setup mode
1. Press and hold the STOP button and the INPUT button. The two buttons
must be pressed within 0.1 seconds of each other and held down for 2
seconds. The device indicates you are now in Setup mode. See below for
available modes.
2. Press the EXIT key when you are finished.
Note: Your settings will not be lost in the event of battery removal or failure.
Transmit Mode
Press button 1 to select from one of the different available transmit modes. The
transmit mode changes each time 1 is pressed. The predetermined modes are
IR 38 Khz, IR 455 Khz, ZigBee Mode, IR 38 + Zig, and IR 455 + Zig. The
display indicates the selected mode.
Timeout Adjustment
Press button 2 on the remote to change the sleep timeout from the default.
Each time 2 is pressed, the sleep timeout raises incrementally. The pre-
determined sleep timeouts are 3, 6, 9, and 12 seconds. The display indicates
the selected sleep timeout.
Download Mode
In order to download new firmware or a new configuration or font file to the MIO
R-3 remote using the remote's program port, the remote must first be placed
into Download mode. Press 3 on the remote to toggle the Download mode OFF
and ON. The Download mode must be ON before you can download a file to
the MIO R-3. While the Download mode is ON, the device will not go to sleep.
Once the download is complete, this setting must be returned to Download Off.
A firmware download will cause the remote to reset and this will automatically
reset the remote to Download Off.
Debug Mode
Pressing button 4 on the remote toggles Debug mode between ON and OFF.
Pressing the button toggles to the new mode; 2 seconds after selecting the
mode, the menu returns to Setup mode. The remote will remain in the last
mode selected until Setup mode is once again entered and this mode is
changed by pressing the 4 button.
Firmware Version
Pressing button 5 on the remote displays the remote and ZigBee firmware
versions currently loaded on the remote. To view the available firmware
versions, press the Move Up arrow on the scroll wheel to scroll up. and
pressing the Move Down arrow will scroll down. When finished, press Exit to
save the changed firmware information and leave Setup mode.
Device ID
Pressing button 6 displays the device’s Device ID number. To change the
Device ID number, press the Move Up arrow on the scroll wheel to scroll up.
and pressing the Move Down arrow will scroll down. To move the cursor to the
next number, use the Move Left or Move Right arrows on the scroll wheel to
change positions.
After all numbers have been configured as desired, pressing the center button
on the scroll wheel will store the entered Device ID into memory. After the
Device ID is stored into memory, the display will return to Setup mode.
LED Awake Brightness
Pressing button 7 on the remote toggles the Power LED Brightness mode from
LOW to MED and then HIGH. The display indicates the selected mode.
LED Sleep Mode Brightness
Pressing button 8 on the remote toggles the Sleep Brightness mode from OFF
to LOW and then MED. The Sleep brightness is the state the MIO R-3 assumes
while in the charging cradle.
ZigBee ID PAN, Channel and System Connection
Pressing the 9 button will display the current Extended ZigBee Personal Area
Network (PAN) ID and channel for the device. In order to display the NetLinx
Master IP and ZigBee gateway EUI addresses, press the Move Up arrow on
the scroll wheel to scroll up. and pressing the Move Down arrow will scroll
down. When finished, press Exit to save the Extended PAN ID and channel
information and leave Setup mode.
Site Survey
Pressing the 0 button makes the MIO R-3 scan all frequencies and store all
joinable Extended PAN IDs and Channels in memory. The display will show the
first accessible Extended PAN ID and Channel.
To display other Extended PAN IDs and Channels found in the area, press the
Move Up or Move Down arrows on the scroll wheel until the remote displays
the desired Extended PAN ID and Channel.
To connect to a particular Extended PAN ID, pressing the center button on the
scroll wheel will initiate the remote to connect to a network. If no networks were
found, the display will read SCAN FAIL before returning to Setup mode.
Programming The MIO R-3 Using KeypadBuilder
Most functionality of the MIO R-3 is handled using the KeypadBuilder
application. Go to www.amx.com for the supporting documentation.
The MIO R-3 recognizes a select number of Serial Commands and
SEND_COMMANDs. For a full list and descriptions, consult the Programming
section of the MIO R-3 instruction manual at www.amx.com.
Using the Programming Jack on The MIO R-3
The programming jack (see FIG. 2) is used for communication between the
device and KeypadBuilder. The programming jack uses a three-wire, 2.5mm
stereo jack, and you can order the programming cable (FG10-817) from AMX if
you do not currently possess one.
To download KeypadBuilder Configuration Files:
1.
Set the MIO R-3 Download mode to ON.
2. Flip and turn the device so that the buttons are facing away from you and
the device is upside down.
3. Holding the device in both hands, place your thumbs on the battery door
and slide the battery door free. The battery door will slide in the direction
of the bottom end of the device.
4. Connect the 2.5mm stereo plug (male) end of the programming cable
(FG10-817) into the programming jack on the bottom side of the remote
device.
5. If necessary, connect the DB-9 end of the programming cable to the
female DB-9 connector on the DB-9 extension cable (FG10-727).
6. Connect the female DB-9 terminal end of the extension cable to the port
on the back of your computer.
7. Configure the communication parameters in KeypadBuilder.
Patents
This product is covered by the following patents:
AMX
U.S. Patent No. D 602,858
U.S. Patent No. D 520,495
U.S. Patent No. 7,786,623
This product employs or practices certain features and/or methods of one or
more of the following patents:
SIPCO, LLC
U.S. Patent No. 7,103,511
U.S. Patent No. 6,914,893
U.S. Patent No. 7,697,492
FIG. 3 Rechargeable Battery Port on The MIO R-3 Remote
Lithium-Ion Battery
Rechargeable
Battery
Port Connection
Correct path for
battery wires and
connector