Poulan Pro PR625Y22RKP LAWN MOWER - Manual (Page 5)

24
MODELS WITH GEARCASE-MOUNTED
BELT KEEPER AND
NO DEBRIS SHIELD:
• Remove drive cover.
• Remove spring and belt keeper.
• Remove belt from gearcase pulley.
• Route the other end of the new drive belt
through hole in housing.
• Return mower to upright po si tion.
• Install new belt on gearcase pulley.
• Reinstall belt keeper and spring.
• Reinstall drive cover.
NOTE: Always use factory approved belt
to assure proper fi t and long life.
• Turn lawn mower on its side with air fi lter
and car bu re tor down.
• Reinstall blade and blade adapter.
ENGINE
CARBURETOR
The carburetor has been preset at the fac-
tory and ad just ment should not be neces-
sary. However, minor ad just ment may be
required to compensate for differences in
fuel, temperature, altitude or load.
• The air fi lter must be assembled to the
car bu re tor when running engine.
• Best carburetor adjustment is obtained
when fuel tank is 1/4 full.
• In order for the engine to run, the opera-
tor presence control bar must be held
in the operating position. There fore,
and assistant will be required to hold
the control bar in the operating position
when making fi nal adjustment to the
car bu re tor.
See the ADJUSTMENT section of your
engine manual for further instructions.
ENGINE SPEED
The engine speed has been factory set.
Do not attempt to increase engine speed
as it may result in personal injury. If you
believe the engine is running too fast
or too slow, take your lawn mower to an
authorized engine service center for repair
and adjustment.
THROTTLE CONTROL
If it becomes necessary to adjust or re-
place the throttle control, see the ADJUST-
MENT section of your engine man ual.
Belt
Drive
cover
Belt
keeper
Gearcase pulley
Spring
Blade
bolt
Crankshaft
keyway
Hardened
washer
Lockwasher
Blade adapter Key
Blade
Trailing edge
Belt
retainer
• Turn lawn mower on its side. See
engine manual for proper direction of
turning over the engine.
• Remove blade and blade adapter.
• Remove belt from blade adapter.
• Position the blade adapter on the engine
crank shaft. Be sure key in adapter and
crankshaft keyway are aligned; and that
the drive belt is inside the tabs of the
belt retainer.
5
3 POSITION “QUICK” HANDLES
• Raise lower handle section to operating
position and squeeze the bottom ends
of lower handle towards each other until
the pin in handle can be inserted into
one of the three height adjustment holes.
3 POSITION “EZ” HANDLES
• Raise lower handle section to operating
position and align hole in handle with
one of three height positioning holes.
• Insert handle bolt through handle and
bracket and secure with knob.
• Repeat for opposite side of handle.
Handle
ad just ment
brack et
Knob Bolt
Handle pin
Handle
ad just ment
bracket
SQUEEZE
ALL HANDLES
• Raise upper handle section into place on
lower han dle, remove protective padding
and tighten both handle knobs.
• Remove handle padding holding opera-
tor pres ence control bar to upper handle.
• Your lawn mower handle can be ad-
justed for your mowing comfort. Refer to
“ADJUST HANDLE” in the Service and
Adjustments section of this manual.
NOTE: For shipping purposes, the rear
wheels on your lawn mower may not be
adjusted to the same position as the front
wheels. Before operating mower adjust all
wheels to the same cutting height.
INSTALL REAR WHEELS
(HIGH WHEEL MOWERS ONLY)
Some high wheel models require wash ers
which will be pro vid ed in a parts bag. If provid-
ed, install washers on the axle fi rst as shown.
• Install one (1) rear wheel on the axle of
rear wheel adjuster.
• Install 3/8-16 locknut and tighten securely.
• Repeat procedure for other rear wheel.
MOWING
POSITION
Lower handle
LIFT
UP
Operator
presence
control bar
Upper
handle
LIFT
UP
Handle
knob
AS SEM BLE GRASS CATCHER
(REAR DISCHARGE MOWERS ONLY)
IMPORTANT: If your model lawn mower
is mulcher ready, the mulcher plate or plug
must be removed before using mower as
a bagger. To convert mower to bagging or
discharging, see the Operation section in
this manual.
Look at the different grass catcher illustra-
tions that follow. Determine which type
of grass catcher you have and follow the
appropriate instructions.
Flanged
locknut Wheel
assembly
Washer
Axle
O-Ring