Poulan Pro PR625Y22RKP LAWN MOWER - Manual (Page 9)

20
Debris shield
Drive belt
Belt retainers
DEBRIS SHIELDS WITH BELT RETAINERS:
Belt
Drive
cover
PUSH
DOWN
Pulley
OR:
Debris shield
Drive belt
Belt
retainer
Engine pulley
3 POSITION “QUICK”
The handle on your lawn mower has three
(3) height positions - adjust to height that
suits you.
• Squeeze the bottom ends of lower
handle towards each other until the pin
in handle can be inserted into one of the
three height adjustment holes.
High
Handle
adjustment
bracket
Handle pin
Medium
Low
SQUEEZE
REAR DEFLECTOR (IF EQUIPPED)
The rear defl ector, attached between the
rear wheels of your mower, is provided to
minimize the pos si bil i ty that objects will
be thrown out of the rear of the mower
into the operator mowing position. If the
defl ector becomes dam aged, it should be
replaced.
TO REMOVE / REPLACE DRIVE BELT
FRONT WHEEL DRIVE MODELS:
“STANDARD” OR “DUAL BAIL” MODELS:
• Remove drive cover. Remove belt from
gearcase pulley by pushing down on
pulley and rolling belt off it.
• Turn lawn mower on its side. See
engine manual for proper direction of
turning over the engine.
• Remove blade.
• Remove debris shield.
• Remove belt from engine pulley on
crankshaft.
• Place new drive belt in the belt retainers
of the debris shield (if equipped).
• Install new belt by reversing above steps.
NOTE: Always use factory approved belt
to assure fi t and long life.
9
Slots
Mulcher
plate tabs
FOR MULCHING MOWERS ONLY
Most mulching mowers are shipped ready
to be used as a mulcher.
“REAR DISCHARGE ONLY” MOWERS
Some models have a seperate mulcher
plug, other models have the mulcher plug
built into the rear door. To convert to bag-
ging or discharging, the plate or plug (if
so equipped) must be removed from the
dis charge open ing of the lawn mower.
• Open rear door and remove mulcher
plate or plug (if so equipped). Store
mulcher plate or plug in a safe place.
• You can now install grass catcher or
optional clipping defl ector accessory.
• To return to mulching operation, install
mulcher plate or plug into discharge
opening of mower.
CAUTION: Do not run your lawn mower
without mulcher plate/plug in place or ap-
proved clipping defl ector or grass catch er
in place. Never attempt to op er ate the
lawn mower with the rear door removed or
propped open.
MULCHER "PLUG"
Mulcher
plug
MULCHER "PLATE"
MULCHER PLUG BUILT INTO REAR DOOR
“SIDE DISCHARGE ONLY” MOWERS
MULCHER PLATE TYPE
To convert to bagging or discharging,
mulcher plate must be removed from un-
derside of lawn mower.
• Remove the four (4) screws and lock nuts
securing the mulcher plate to the mower.
• Store mulcher plate and hardware in a
safe place.
• Mower can now be used for side
discharging or op tion al grass catcher
accessory can be attached.
• To return to mulching operation, simply
reinstall mulcher plate and tighten hard-
ware securely.
Mulcher plate
Screw and
lock nut
MULCHER PLUG TYPE “A”
To convert to mulching operation, mulcher
plug must be installed into discharge open-
ing of mower.
• Open discharge guard.
• Insert tab of mulch plug into housing
opening.
• Align hooks of mulch plug over hinge
rod of discharge guard. Push mulch plug
down until mulch plug is seat ed in hous-
ing opening.
CAUTION: Do not run your lawn mower
without discharge guard, ap proved grass
catcher or mulcher plug in place.
Hooks
Housing
opening
Mulcher plug
Hinge rod
Tab
Discharge
guard