Alpine Multimedia ManagerTM PXI-H990 - Manual (Page 12)

11
-EN
Connect to:
Connect to the DVD Audio
terminal of the DVI-9990 head
unit, etc., using the DVD Audio
Link cable.
Connect to the microphone
(supplied with the main unit) or
the separately sold monitor
(TMI-M990) Road EQ
microphone terminal.
Connect to a computer's USB
terminal with a USB cable (mini
B type).
Connect to the vehicle’s body
using the ground cable.
Connect to amplifier.
Connect to a cable to which
power is constantly supplied.
Connect to the IONBUS
terminal using the IONBUS
cable.
Connect to any product with an
audio output terminal using
RCA-type connectors.
Connect to amplifier.
Terminal specification
• DVD Audio Link terminal
Terminal for DVD audio playback.
• Microphone terminal
Connect microphone.
Connect to the microphone terminal with the supplied microphone
terminal connection cable when using the separately sold monitor
(TMI-M990) internal Road EQ microphone.
• USB terminal
Used to make settings and adjustments with a
computer. USB cable (mini B type) and computer
software are required. For details, contact your
store of purchase or an Alpine Information Center.
• Ground terminal
Connect securely to a metal part of the vehicle’s
body using the ground cable.
• Remote OUT terminal
Connect to the amplifier or other peripheral device.
• Battery power terminal
Power is supplied constantly to the PXI-H990
regardless of whether the engine key is on or off.
• IONBUS terminal
Use when connecting with an IONBUS
compatible terminal or upgrading the system.
• Audio input terminal (RCA input)
Accepts an audio signal output from videos etc.
Connect using an RCA cable.
• Audio output terminal (RCA output)
Outputs an audio signal.
< Side Panel >
*1 There is no OFF setting.
*2 It is not possible to turn both “MID” and “WF” off.
If one is set to “OFF”, the other cannot be set to “OFF”.
Memo
Memo
• Remove the DVD Audio link, IONBUS or USB terminal covers when connecting
the DVD Audio Link cable, the IONBUS cable or the USB cable.
Leave the covers on when not using the DVD Audio link, IONBUS or USB terminal.
• It is necessary to change the setting corresponding with the speaker (system).
(See “Setting the speakers” on the Owner’s Manual)
• Do not connect the tweeter (TW) to the channel without “TW” indicated in the table
above. If connected, the speaker may be damaged.
• For SYSTEM 1, REAR TW cannot be connected.
• For SYSTEM 3, FRONT TW and REAR TW cannot be connected.
* Depending upon the system configuration, the outputs will drive different types of speaker drivers.
CH-1
CH-2
CH-3
CH-4
CH-5
CH-6
CH-7
CH-8
SYSTEM1
Front L TW
Front R TW
Front L WF
* 1
Front R WF * 1
Rear L
Rear R
Front C
Sub WF
SYSTEM2
Front L TW
Front R TW
Front L MID
* 2
Front R MID * 2
Front L WF
* 2
Front R WF
* 2
Sub WF 1
Sub WF 2
SYSTEM3
Front L * 1
Front R
* 1
Front C
Sub WF 1
Rear L
Rear R
Rear C
Sub WF 2
SYSTEM4 (Front)
Front L TW
Front R TW
Front L MID * 2
Front R MID * 2
Front L WF
* 2
Front R WF * 2
Front C TW
Front C WF
SYSTEM4 (Rear)
Rear L TW
Rear R TW
Rear L WF
Rear R WF
Rear C TW
Rear C WF
Sub WF 1
Sub WF 2
When one PXI-H990 is connected When two PXI-H990s are connected