Kasco Marine 4400HJF - Manual (Page 4)

4
Set of 5 Interchangeable Nozzles (5)
1. 3/8” x 2.25” bolt (1)
2. 3/8” x 4” bolt (1)
3. Linden Nozzle (1)
4. Sequoia Nozzle (1)
5. Juniper Nozzle (1)
6. Willow Nozzle (1)
7. Cypress Nozzle (1)
8. Collar for Cypress Nozzle (1)
Also Included:
• Mooring Rope Tube Weights (2)
• Cord in separate box (1) (depending on size of
cord)
• Control Box (C-25 for 120V units in Float box
or C-85 for 240V units in separate box) (1) (Not
Pictured)
TOOLS & SUPPLIES NEEDED
• Anchors or stakes for installing unit (2)
• # 2 Phillips head screw driver
• 120V or 240V Electrical Supply near pond on a
post with room for mounting the C-25 or C-85
• #10 x 1” long or longer screw(s) for mounting the
C-25 (3) or C-85 (4)
• 9/16” Socket and Ratchet
• 9/16” Wrench
• 11/32” wrench (for #8 fasteners)
3400JF, 3400HJF Assembly
1. Make sure you have all the parts needed. If any short-
ages are found, contact your Kasco representative immedi-
ately.
2. Set motor housing upright (stainless steel can down) on
a flat surface.
3. Peel off the adhesive on one of the Cushions for the
fountain housing legs (Part 8). Stick to the top of the foun-
tain housing leg and repeat for the other three cushions.
3400JF, 3400HJF Parts Included
1. 3400JF Aerating Fountain (Unit with cord or unit
with Disconnect) (1)
2. Float (with two 50’ mooring ropes attached) (1)
3. 1/4-20 x 3 1/2” Phillips Pan Head Screw (4)
4. 1/4” split washers (4)
5. 1/4” (3/4” outer diameter) Flat Washer (4)
6. 3/8”-16 x 1-3/4” Hex Head Bolt (2)
7. 3/8” Flat Washer (4)
8. Cushions for Legs (4)
9. Bottom Screen section (3)
10. Bottom Screen Clips (2)
11. 3/8”-16 Nylon Lock Nut (2)
12. #8 nut (6)
13. #8 flat washer (12)
14. #8 lock washer (6)
15. #8 x 1/2” Screw (6)
1
2
3
4
5
6
7
8
9
12
10
11 13 14 15
REV. ECO# DESCRIPTION DR'N BY DATE DES ENG CH'K BY
1 INITIAL RELEASE
XXXX-XXXX-XX
DO NOT SCALE DRAWING
C.A.D. GENERATED DRAWING
800 DEERE ROAD
PRESCOTT, WI 54021-1241
X
FX FLOAT ASSEMBLY W/SCREEN
X
X
X
X
THIS DRAWING CONTAINS PROPRIETARY
INFORMATION AND SHALL NOT BE USED,
REPRODUCED OR DISTRIBUTED WITHOUT
THE PRIOR WRITTEN CONSENT OF
KASCO MARINE, INCORPORATED
.X .02 [.508] .XX .010 [.254]
.XXX .005 [.127] ANGULAR 0.5
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES.
DIMENSIONS IN [ ] ARE MILLIMETERS.
TOLERANCES ON:
THIS DOCUMENT HAS BEEN ISSUED
FOR ENGINEERING INFORMATIONAL
PURPOSES ONLY. ANY REVISIONS
TO THE CONTENT OF THIS DOCUMENT
MUST BE INCORPORATED INTO THE
ORIGINAL CAD FILE.
THIRD ANGLE PROJECTION TITLE:
XXXX-XXXX-XX
SHEET 1 OF 1
FINISH:
MATERIAL:
SCALE: 1:24
DWG. NO.