ID Innovations Bar code Slot Reader - Visible Red and Infra Red - Manual (Page 13)

Features
13
CODE 39: Control Character Override: OFF
Use this option to disable all Edits, Macros, Strings, and the Type ID for CODE 39 bar codes that contain control characters.
When this option is enabled and a CODE 39 containing control characters is read, the special key macros are applied, and the
data is transmitted to the computer. With this option enabled, you can use bar codes with special control characters to control the
computer system without going through the standard editing procedures.
Select Option Group: CODE 128
Select this option group to modify the individual settings for the CODE 128 decoder. Once you have selected this option group,
you may cursor down to configure each of the following decoder options.
CODE 128: Decoder: ON
 
Use this option to enable or disable the CODE 128 decoder. The default for this option is ON.
CODE 128: Maximum Length: 164
CODE 128: Minimum Length: 0
 
Use these options to configure the minimum and maximum lengths of CODE 128 bar codes that can be read. If you configure the
Maximum Length to 10 characters and the Minimum Length to 5 characters, the decoder will not read CODE 128 bar codes with
less than 5 characters and more than 10 characters.
CODE 128: Type ID: g DEC 103 HEX 67
 
Use this option to configure the Type ID for the CODE 128 bar code. Type ID's can be transmitted as a prefix or a suffix to the bar
code data, for more information see OTHER: Send Bar Code Type ID on page 15.
CODE 128: Control Character Override: OFF
 
Use this option to disable all Edits, Macros, Strings, and the Type ID for CODE 128 bar codes that contain control characters.
When this option is enabled and a CODE 128 containing control characters is read, the special key macros are applied, and the
data is transmitted to the computer. With this option enabled, you can use bar codes with special control characters to control the
computer system without going through the standard editing procedures.
Select Option Group: INTERLEAVED 2 OF 5 GROUP
Select this option group to modify the individual settings for the INTERLEAVED 2 of 5 decoder. Once you have selected this
option group, you may cursor down to configure each of the following decoder options.
INTERLEAVED 2 OF 5: Decoder: ON
 
Use this option to enable or disable the INTERLEAVED 2 of 5 decoder. The default for this option is ON.
INTERLEAVED 2 OF 5: Check Digit: OFF
 
For applications requiring enhanced data security, a check digit can be used on INTERLEAVED 2 of 5 bar codes. When used, the
check digit immediately follows the last data character. Use this option to choose between the type of INTERLEAVED 2 of 5 check
digit, select from MOD 10, OPCC, or OFF (None).
INTERLEAVED 2 OF 5: Send Check Digit: OFF
 
Some applications may require that you use a check digit in the bar code for security but do not require the check digit be
transmitted to the computer. Use this option to have the decoder either send the check digit to the computer or remove the check
digit from the transmitted data.
INTERLEAVED 2 OF 5: Maximum Length: 100
INTERLEAVED 2 OF 5: Minimum Length: 4
 
Use these options to configure the minimum and maximum lengths of INTERLEAVED 2 of 5 bar codes that can be read. If you
configure the Maximum Length to 10 characters and the Minimum Length to 5 characters, the decoder will not read
INTERLEAVED 2 of 5 bar codes with less than 5 characters and more than 10 characters.
Note: The Maximum and Minimum Length options are ignored if you enable the Fixed Length option.
INTERLEAVED 2 OF 5: Fixed Length: OFF
 
Use this option to configure the INTERLEAVED 2 of 5 decoder to read only fixed length bar codes. When this option is enabled
the following two prompts (Fixed Length #1 and Fixed Length #2) are used to set the two different sizes of INTERLEAVED 2 of 5
bar codes that will be allowed.