Staub Electronics AA-SF-16M AUDIO AUTHORITY - 16 CHANNEL MATRIX AMPLIFIER WITH FLEXPORT INPUTS - Manual (Page 9)

SF-16M Matrix Amplifier Installation and Operation Guide 9
FlexPort Cat 5 Audio Inputs
The SF-16M includes two FlexPort Cat 5 inputs that accept a variety of pro and consumer
audio sources via optional FlexPort audio modules. See Appendix A for a detailed over-
view of all FlexPort modules and system configuration.
FlexPort module options include:
FPM-B Balanced line/mic with phantom power
FPM-X XLR/ 1/4” TRS with phantom power
FPM-D Digital optical/coax
FPM-U Analog RCA
Understanding the FlexPort Audio Bus
Each SF-16M FlexPort input supports:
• Two channels of audio - input can be either stereo or two mono channels (allows two
mono inputs per FlexPort bus)
• RS-485 data pathway - provides 2-way communication between the SF-16M and all
connected FlexPort modules
• 18V power - provides power for two FlexPort modules on a single bus
Daisy Chain FlexPort Modules For Two Mono Inputs Per Bus
All FlexPort audio modules feature a FlexPort Bus In and Out, so two modules may be daisy chained together for a two
mono source setup. In daisy chain scenarios, it is required to assign one module as “Mono 1” and the other module as
“Mono 2” using the dipswitches located on the back of the FlexPort modules. See Appendix ? for more information. Fig-
ure 4 below illustrates a daisy chain configuration.
Figure 4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SPEAKER OUTPUTS (CLASS 2 WIRING)
ETHERNET
USB
RS-232 IN
RS-232 OUT
LINK
SPEED
701-13303B
MAIN IR
IN
MAIN IR
OUT
UNIT ID
DB25 AUDIO INPUT
CONTACT CLOSURE 5V - 24V AC / DC
AUDIO LOOP OUTPUT
LINE INPUTS
BUS
FlexPort 1
OUT IN
1 2 IN OUT
SYSTEM
TRIGGER
AUDIO
OVERRIDE
100-120V~ 50-60 Hz
1125W
Replace Fuses Only
with T 10A, 250V
Remplacer Uniquement
avec Fusible T 10A, 250V
Set voltage selector
and install correct
fuses according to
local power supply.
Régler le sélecteur
de tension et
installer les fusibles
corrects selon
l’alimentation locale.
4002715
1 3 5 7 9 11 13 15
A B C D E F G H
2 4 6 8 10 12 14 16
L
R
16BN4020
701-13303
SF-16M 120V Rear Panel Artwork
1/2
ETL LISTED CONFORMS
TO UL STD 60065
CERTIFIED TO CAN/CSA
STD C22.2 NO. 60065
Audio Authority® Corp. • 2048 Mercer Rd. Lexington, KY 40511 USA
800-322-8346 • 859-233-4599 • www.audioauthority.com
Model SF-16M 16-Channel Matrix Amplifier PDF User Manual
VOLTAGE SELECTOR
FlexPort 2
OUT IN
STEREO ZONE 1 STEREO ZONE 2 STEREO ZONE 3 STEREO ZONE 4 STEREO ZONE 5 STEREO ZONE 6 STEREO ZONE 7 STEREO ZONE 8
FPM-U
FPM-U
FPM-U
FPM-U
FPM-B
IN
OUT
IN
OUT
IN
OUT
BUS
IN
BUS
OUT
ASSIGN
CHANNEL
DUAL M
MONO 1
MONO 2
INPUT
MIX
OVER-
RIDE
BUS
PWR
FLEXPORT 761-392
MIC
ON
ON
MOMENTARY
TERM. ON
PHANT. OFF
LINE
OFF
OFF
TOGL.
OFF
ON
SWITCH
GAIN
MIN
MAX
FPM-D and FPM-U: These are natively stereo
input modules - Dipswitch setting should be
“Stereo”.
FPM-B and FPM-X: These are natively mono input
modules - If one mono source input is desired on both
FlexPort bus audio channels, the dipswitch setting
should be set to “Dual M” for dual mono.
Figure 5
BUS
IN
BUS
OUT
ASSIGN
CHANNEL
STEREO
MONO 1
MONO 2
MIX
OVER-
RIDE
BUS
FLEXPORT 761-391
ON
ON
MOMENTARY
TERM. ON
OFF
OFF
TOGL.
OFF
SWITCH
GAIN
MIN
MAX
BUS
IN
BUS
OUT
ASSIGN
CHANNEL
DUAL M
MONO 1
MONO 2
INPUT
MIX
OVER-
RIDE
BUS
PWR
FLEXPORT 761-392
MIC
ON
ON
MOMENTARY
TERM. ON
PHANT. OFF
LINE
OFF
OFF
TOGL.
OFF
ON
SWITCH
GAIN
MIN
MAX
FPM-D
FPM-B FlexPort module rear view
SF-16M FlexPorts
Single FlexPort Module Connection For One Stereo or Dual Mono Input
When connecting a single FlexPort audio module to a FlexPort bus input (See figure 5 below) it is necessary to configure
the audio modules as shown below.