Alpine IDA-X303 - Manual (Page 32)

30
-EN
• If IMPRINT audio processor is connected, you can make more
detailed settings for the audio setting. For details, refer to “IMPRINT
Operation (Optional)” (page 29).
Storing the Audio Adjustment Level
You can store up to 3 adjusted/set contents on this unit.
All of the following adjusted/set items are stored in a preset
memory.
1
Turn the Double Action encoder to select a preset
number, and press and hold
/ENTER for at least
2 seconds.
2
Turn the Double Action encoder to select
PROTECT YES/NO, and then press
/ENTER to
store the adjusted contents.
PROTECT YES (Initial setting) PROTECT NO
• If YES is selected, the adjusted contents are protected and stored into
the preset numbers. When you want to store the parameter into a
protected preset number, “REPLACE NO/YES” can be selected.
• If PROTECT NO is selected, the preset is stored.
• While perform this operation, all adjusted contents of Parametric
EQ/Graphic EQ, Time Correction and X-Over will be stored in the
preset number.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
Recalling the Audio Adjustment Level
You can recall the contents stored in “Storing the Audio Adjustment
Level” (page 30).
1
Turn the Double Action encoder to select a preset
number, and press
/ENTER.
Adjusted/set contents of the selected number are recalled.
• The User Preset screen can also be recalled in normal mode by
pressing and holding PRESET for at least 2 seconds.
When the Media Xpander is on, you can adjust the Media Xpander level
(refer to page 33).
OFF (Initial setting) ON
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
FLAT POPS ROCK NEWS JAZZ&BLUES
ELECTRICAL DANCE HIPHOP&RAP
EASY LISTENING COUNTRY CLASSICAL USER1
USER2 USER3 USER4 USER5 USER6
• By selecting User’s 1 to 6, you can recall the stored preset number in
“Adjusting the Graphic Equalizer Curve” (page 31) or “Adjusting
the Parametric Equalizer Curve” (page 30).
The setting of Parametric EQ/Graphic EQ Adjustment, Time Correction
and X-Over can be adjusted in this mode.
Adjusting the Parametric Equalizer Curve
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste. To adjust the Parametric Equalizer
Curve, set the EQ mode to PARAMETRIC EQ. For details, refer to
“Setting EQ mode” (page 32).
1
After selecting EQ ADJ (Parametric EQ) from the
Sound Field Adjustment mode, turn the Double
Action encoder to select the band adjustment, and
then press
/ENTER.
BAND1 BAND2 BAND3 BAND4 BAND5 BAND1
2
Turn the Double Action encoder to select an item
to adjust, then press
/ENTER.
Frequency Adjustment
3
-1 Turn the Double Action encoder to select
frequency bands.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
BAND1: 20 Hz~80 Hz (63 Hz)
BAND2: 50 Hz~200 Hz (150 Hz)
BAND3: 125 Hz~3.2 kHz (400 Hz)
BAND4: 315 Hz~8 kHz (1 kHz)
BAND5: 800 Hz~20 kHz (2.5 kHz)
Level Adjustment
3
-2 Turn the Double Action encoder to adjust the
level.
Adjustable level: –6 to +6 dB
Bandwidth (Q) Adjustment
3
-3 Turn the Double Action encoder to set the
bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
4
To adjust another band, repeat steps 1 to 3 and
adjust all bands.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
• You can select the next band by pressing and turning the Double
Action encoder.
• The User Preset screen can be recalled in the normal mode by
pressing and holding PRESET for 2 seconds.
USER PRESET
Items to be adjusted/set Reference page
EQ ADJ (Parametric EQ/Graphic EQ) page 30~page 31
TCR page 31
X-OVER page 31
Turning Media Xpander ON/OFF
Equalizer Presets (Factory’s EQ) (FR-EQ)
Sound Field Adjustment
FC LV Q FC
(frequency) (level) (bandwidth) (frequency)