Steelcraft Automotive 55100 GRILL GUARD - Manual

PARTS LIST:
1 Grille Guard 2 10-1.50mm x 30mm Hex Head Bolts
1 Passenger Side Mounting Bracket (A) 8 10mm Thick Flat Washers
1 Driver Side Mounting Bracket (D) 4 10mm Nylock Nuts
1 Passenger Side Top Bracket (B) 2 10mm Nut Plates
1 Driver Side Top Bracket (C) 2 10-1.50mm x 40mm Hex Head Bolts
2 8-1.25mm x 25mm Hex Head Bolts 4 12-1.75mm x 30mm Hex Head Bolts
4 8mm ID x 22mm OD x 3mm Flat Washers 8 12mm Thick Flat Washers
2 8mm Nylock Nut 4 12mm Nylock Nuts
2 10-1.50mm x 25mm Allen Bolts
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY.
2. Using a flat screwdriver carefully remove all fasteners from factory plastic shroud on top and underneath the
vehicle. On the bottom there are (4) on the front and (3) on each side by the fender. On the top there are (7)
fasteners.
3. Remove bottom plastic shroud and place it on a working area. Using a hack saw carefully cut the marked
area shown in Figure 1.
4. Re-install the bottom factory plastic shroud with original fasteners. NOTE: Do not install the two fasteners
shown in Figure 1.
5. Slide Passenger Side Mounting Bracket through the previously cut out slot on the plastic shroud and
position bracket to its mounting location (Figure 2). NOTE: Rear hole on the Mounting Brackets should line
up with the holes on the plastic shroud as well.
6. Install the rear of the Passenger Side Mounting Bracket to existing hole on the sub-frame with the included
(1) 10-1.50mm x 30mm Hex Head Bolt, (1) 10mm Nylock Nut, and (2) 10mm Flat Washers(Figure 2). Do not
tighten hardware at this time.
7. Install the front of the Passenger Side Mounting Bracket to the existing hole on the factory bumper with the
included (1) 10-1.50mm x 40mm Hex Head Bolt, (1) 10mm Flat Washer, and (1) 10mm Nut Plate (Figure 2).
Do not tighten hardware at this time. IMPORTANT: Before you thread Bolt into Nut Plate, make sure
you measure the bolt. The bolt should measure no more than 40mm / 1 9/16”. If the bolt is longer
than 40mm / 1 9/16”, contact your local retailer. Do not attempt to install the bolt if it is longer than
40mm / 1 9/16”, doing so will cause damage the radiator.
8. Repeat steps 5-7 for driver side Mounting Bracket.
9. Locate the passenger side Top Bracket and slide it through top section of factory grille shell.
10. Install the inner side on the Top Bracket to the existing hole on the radiator support with the included (1)
8-1.25mm x 25mm Hex Head Bolt, (1) 8mm Nylock Nut, and (2) 8mm Flat Washers (Figure 3 & 4). Do not
tighten hardware at this time.
11. Repeat step 9 &10 for Driver Side Top Bracket.
12. With help position Grille Guard on the inner side of the Mounting Brackets. Attach Grille Guard to Mounting
Brackets with the included (4) 12-1.75mm x 30mm Hex Head Bolts, (4) 12mm Nylock Nuts, and (8) 12mm
Flat Washers (Figure 2). Do not tighten hardware at this time.
Page 1 of 2
2/22/07 (AM)
INSTALLATION INSTRUCTIONS
GRILLE GUARD
07 HONDA CRV
PART NUMBER
(A)
(B) (C)
(D)