System Sensor CZ-6 - Manual (Page 3)

D500-49-00 3 I56-1799-005
Step 1: Insert the bottom of the CZ-6 module down into a
rear slot on the chassis.
Step 2: Carefully swing the upper edge of the board back towards
the back of the chassis until it touches the two standoffs.
Step 3: Align two 4-40 screws with the two standoffs and tighten.
Step 4: Address and wire the modules according to the instruc-
tions in this manual.
The steps in Figures 6a and 6b describe and illustrate module in-
stallation when the rear chassis position and the position in front
of it will be filled. Front position installation is possible only if the
rear position is filled with another module.
Figure 6a. Installation of CZ-6 module in a rear
chassis position, method two:
1
Step 1: Insert the bottom edge of the CZ-6 module down into a
rear slot of the chassis.
Step 2: Carefully swing the upper edge of the board towards the
back of the chassis until it touches the short standoff at-
tached to the chassis.
Step 3: Align the long standoff with the short standoff and tighten.
Figure 6b. Installation of CZ-6 module in front
chassis position:
2
3
1
Step 1: Insert the bottom edge of the CZ-6 module down
into a front slot of the chassis.
Step 2: Carefully swing the upper edge of the board
towards the back of the chassis until it touches the 1 1 /
4
˝
(31.75mm) standoffs installed on the rear module.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Statement
C0225-00
C0226-00
Step 3: Align two 4-40 screws with the two standoffs and tighten.
Step 4: Address and wire the modules according to the instruc-
tions in this manual.
WIRING
NOTE: All wiring must conform to applicable local codes,
ordinances, and regulations.
1. Install module wiring in accordance with the job drawings and
appropriate wiring diagrams.
2. All wiring to the CZ-6 is done via terminal blocks. In order to
properly make electrical connections strip approximately 1/4″
of insulation from the end of wire, sliding the bare end of the
wire under the clamping plate screw.
3. Set the address on the modules per the job drawing. Use the
rotary code switches to set the address of the first module (be-
tween 01 and 94).
In Class B operation, the remaining modules are automati-
cally assigned to the next five higher addresses. For exam-
ple, if the base address switch is set to 28, the next five
modules will be addressed to 29, 30, 31, 32 and 33.
The module is shipped in Class B position, remove shunts for Class
A. When operating in Class A, alternate modules are paired together
(+0/+1, +2/+3, +4/+5), resulting in a total of three modules.
For example, if the base address switch is set to 28, then 30 and 32
will be automatically assigned to the modules while 29, 31 and 33
are available to be used for other modules on the SLC. For Class A
and B operation, DO NOT set the lowest address above 94, as the
other modules will be assigned to nonexistent addresses.
4. A shunt is provided to disable a maximum of two unused modules
in Class B operation and Class A operation. Modules are disabled
from the highest address and work downward. If two modules
are disabled, the lowest four addresses will be functional, while
the highest two will be disabled. For example, in Class B opera-
tion, if the shunt for Address Disable is placed on “two” and the
base switch is set to 28, the modules will be assigned to 28, 29,
30 and 31 while disabling the highest two positions.
NOTE: Place unused shunts on single pin to store on board for
future use.
NOTE: Power must not be applied to the unit when changing
functionality of the shunts.
WIRING NOTES
• Power-limited circuits must employ type FPL, FPLR, or FPLP
cable as required by Article 760 of the NEC.
• All wiring must be in accordance with the NEC, NFPA 72 and
all other applicable codes and standards. All external power
supplies must be power limited with battery back-up. All ex-
ternal power supplies and detectors must be UL listed for fire
protection signaling applications.