Teka HPE 735 - Manual (Page 14)

27
E
N
G
L
IS
H
26
PROGRAMMING AND OPERATING THE PYROLYTIC FUNCTION
Follow the instructions below to carr y out a
pyrolytic cleaning cycle:
1 IMPORTANT: Remove all accessories
(shelves, grids, side supports to hold up
the shelves, telescopic guide rails) from
inside the oven.
2 Turn the cooking control dial to Pyrolysis
position .
3 Next, press the PIRO key, the word PIRO
should appear on the timer display.
4 After a few seconds, P2 (pyrolysis pro-
gramme 2) will appear on the timer display,
the BACK symbol will also remain lit up.
5 You can now change the pyrolysis program-
me to P1, P2 or P3 by pressing the + or –
keys:
P1: Minimum programme. Duration 1 hour
P2: Standard programme. Duration 1 hour
and 30 minutes
P3: Maximum programme. Duration 2
hours
6 You will hear 2 consecutive beeps after
several seconds or by pressing the PIRO
key confirming the chosen programme.
7 You can still change the pyrolysis program-
me by pressing the PIRO key and the + or
– keys.
8 After a shor t time, you will see the time
remaining for the selected programme to
end and the symbols and BACK lit up
on the timer display. The pilot light will
turn on and the oven door cannot be ope-
ned, as the heating will have begun.
IMPORTANT: At this point, the oven is pro-
grammed and the pyrolytic cleaning cycle is
under way. During the cycle, none of the timer
functions can be selected, except the child
lock. Do not tr y to open the oven door as it
may interrupt the cleaning process.
9 When the pyrolytic cleaning cycle has finis-
hed, an alarm will sound, the symbol
will flash and you will see the correct time
on the display.
10 Press any of the timer’s keys to disable the
alarm.
11 Set the cooking control dial to position .
12 The oven’s heating process has ended,
however the oven is extremely hot and can-
not be used. The cooling motor will opera-
te until the oven cools down, pilot light
will remain on and the symbol will
flash on the timer display.
IMPORTANT
The cooling process may last up to 2 hours
owing to the high temperatures inside the
oven.
13 Once the oven has cooled down, pilot light
will automatically turn off.
14 Press the PIRO key to stop symbol 9 flas-
hing. .
IMPORTANT
To open the door (pilot light on), the control
dial must be in position . If you did not follow
instruction 11 set the control dial to position
and wait a few minutes until the door unlocks
and the pilot light switches off.
15 Open the oven door and wipe the inside
with a damp cloth, cleaning up the ash
from the cleaning cycle. Areas in the oven
that are difficult to access will need to be
cleaned with a non-metallic fibre scourer.
16 Once the oven is clean, do not forget to
replace the suppor ts and accessories.
17 The oven is now ready to be used.
IMPORTANT: If any incidents are detected in
the programming and operating of this func-
tion, consult the section “Incidents while
Operating the Pyrolytic Function”.
CANCELLING THE PYROLYTIC CYCLE
Pyrolysis is an automatic function and therefo-
re can only be activated from the timer pro-
gramme. To cancel a cleaning cycle it is neces-
sar y to reset the oven, following the instruc-
tions below:
1 Set the control dial to position .
2 Unlock the oven door.
3 Cancel the pyrolysis programme.
1 Set the control dial to position . The
oven will no longer heat up. Wait a few
minutes before continuing with the instruc-
tions to unlock the door.
2 Unlock the oven door. To cancel the clea-
ning cycle, the oven door must be unloc-
ked. To do so, consider the following:
a) Unlocking the door 30 minutes after
the cleaning cycle. If the oven has been
operating for more than 30 minutes, the
door will unlock automatically once the
oven has cooled down to the safe tem-
perature. Then, pilot light will switch
off.
b) Unlocking the door in the first 30 minu-
tes (at a low temperature). Within the
first 30 minutes the oven door will
unlock automatically. Follow the instruc-
tions below:
1 Turn the control dial to position .
2 Wait for approximately 1 minute.
3 Turn the control dial to position .
4 Approximately, 1 minute later pilot
light will turn off and the oven door
can be opened.
3 Cancel the pyrolysis programme. To can-
cel the programme you must:
1 Turn the control dial to position
and then to position .
2 Press the PIRO key for 3 seconds.
3 Next, the timer display will show the
correct time and symbol will disap-
pear.