AmpliVox TABLETOP LECTERN W/S-250 - Manual (Page 2)

Optional Accessories
Batteries
S-1430
Alkaline D-Cell Batteries; set of 10..............................................$26.00
S-1465 NiCad battery pack; 4.3 amp hours ..........................................$165.00
Power Supply
S-1460
International AC Adapter/Recharger;110/220 volts;50/60 Hz. ......$109.00
W ireless Kits
S-1600
W ireless Lapel Mic Kit ..............................................................$308.00
S-1610 W ireless Headset Mic Kit ..........................................................$374.00
S-1612 W ireless Lapel/Headset Mic Kit ..............................................$374.00
S-1620 W ireless Hand-Held Mic Kit ......................................................$374.00
Microphones
S-2030
Lapel Mic; with 12 ft. extension ..................................................$55.00
S-2040 Headset Mic; with 12 ft. extension ............................................$121.00
S-2030A Hand-Held Mic and Cable ..........................................................$99.00
S-1720 Mic Extension Cord; 25-ft . ..........................................................$65.00
Extra Speaker & Tripod
S-1201
Compact Companion Speaker; black high pressure laminate........$209.00
S-1090 Tripod for speaker ....................................................................$188.00
Light
S-1100
AC Reading Light; clip-on............................................................$55.00
Media Cart Base
S-260
Combines with Tabletop Lectern to form a full-size lectern
or use separately for slide projector, etc. ..................................$197.00
Prices are subject to change without notice
10. Attach the gooseneck. Screw the
gooseneck with mic holder onto the
gooseneck flange. Insert the mic cord
into the mic base. Place the mic into the
mic holder; insert the mic plug into the
dynamic microphone jack.
11. Plug-in the speaker.Plug the speak-
er cord into either the right or left amp
jack. If you have a second external
speaker, connect its 1/4 plug into the
Speaker- R jack Set the amplifier inside
the lectern.
12. Attach the speaker grille by pressing
i
ts posts into the holes on the front of the
lectern.
Refer to the S-805A amplifier operating
instructions for information about the amp
controls.
If you purchased any optional acces-
sories such as a wireless kit, lapel mic,
International AC Adapter/Recharger,
extra speakers, tripods, etc. refer to the
instructions packed with them for installa-
tion and usage information.
Your Tabletop Lectern is now complete.
Thousands of AmpliVox sound products
have been in use since we first began
shipping in 1961. We hope you enjoy
many years of use from your new
Tabletop Lectern.
If you have any questions or comments ,
call customer service line.
1-800-267-5486
6. Attach the front/speaker panel. Make
sure the finished edge of the speaker/front
panel is facing up towards you. Slide
speaker/front panel until the dowel pins of
the right and left side panels are com-
pletely inserted into the Quick-fit connec-
tors of the speaker/front panel. Tighten the
4 Quickfit Connectors in speaker/front
panel 1/2 turn.
7. Attach the bottom. Carefully pick up
and place the Top, Right and Left side
panel assembly on its side with the Top
panel facing opposite of you. Insert the
Bottom Panel under the pins on the Right
and Left side panels by sliding the bottom
panel under pins of the sides. Now slide
the bottom panel until the dowel pins of the
side panels are completely inserted into
the Quick-fit connectors of the bottom
panel. Tighten the 4 Quickfit Connectors
on the bottom panel 1/2 turn.
8. Carefully turn over lectern After tighten-
i
ng Expando Connectors on the bottom of
the lectern, Carefully pick up and turn
over lectern so that the Paper Stop is fac-
ing up.(see illustration above)
S-250 ONLY
9. Install the batteries in the amp. Refer to
the amp instruction sheet for battery
installation information.
4. Attach the left side. Place Top panel on
protected flat surface with dowel pins fac-
ing up. Place the left side panel with the
finished edge facing up onto the top panel
and slide side panel until its dowel pins are
completely inserted into the Quick-fit con-
nectors as far as they can go. The short
edge of the side panel should be towards
the edge of the Top panel that has the
paper stop.
Use a phillips screwdriver
to tighten the 2 Quick-fit Connectors. Turn
only 1/2 turn clockwise. Over tightening
will break the connectors!!
F:\docs\productinstructions\r-
5. Attach the right side panel. Attach the
right side panel using the same instructions
as the left side panel to the top panel and
tighten the 2 Quick-fit Connectors.
Short edge
Top
Left Side Panel
Tighten
Short edge
Top
An
gl
ed
Si
de
Le
f
t
Si
de
P
an
el
Tighten
Paper Stop
Paper Stop
Ri
gh
t
Si
de
Panel
Left Side Panel
Tighten
Le
f
t
Si
de
P
an
el
Gooseneck flange
Paper Stop
An
gl
ed
Si
de