Maple Systems OIT4165A - Manual (Page 5)

5.4. Installing a Slide-In Legend
To replace the factory installed legend with your own:
1. Ensure all paints, inks and fixative are thoroughly dry and will not transfer.
2. Place the unit face down on a clean protective surface.
3. Locate the legend access slot along the right side of the cover.
4. Remove the tape from the existing legend and then pull the legend out.
5. Slide in the new legend (refer to Figure 11).
• be gentle
• avoid wrinkling, which makes it hard to push the legend in
• if the legend moves around too much, put a curl in the paper
NOTE: The legends are made long to facilitate removal.
6. Once installed, tape the end of the legend to the cover to secure it.
20 OIT3165A/4165A
1010-0102, REV 05
Legend Cover
Legend is shown being
installed at a 45º angle
Sectional Side View
(not to scale)
Tape legend to the side of
the cover once in place
Be careful not to abrade the graphics against the edge of the
access slot in the aluminum plate.
A paper "shoehorn" may be used to prevent this.
Gasket
Aluminum Plate
Front of OIT
Figure 11 Custom Keypad Legend Installation
INSTALLATION MANUAL 5
1010-0102, REV 05
Table of Contents
1. Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1. Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Control Panel Design Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1. Control Panel Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2. Power Supply Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3. OIT Cable Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4. Other Steps to Improve Noise Immunity . . . . . . . . . . . . . . . . . . . . . . . . 9
3. OIT Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1. Create Custom Slide-In Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2. Prepare Panel for OIT Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3. Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4. Mount OIT to Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.5. Connect OIT to Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.6. Connect OIT to PLC/Host. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4. OIT Configuration Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1. Connect OIT to PC for Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 15
5. Custom Keypad Slide-In Legends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1. Predefined Keypad Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2. Blank Legend for Photocopying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3. Creating a Computer-Generated Slide-In Legend. . . . . . . . . . . . . . . . . 19
5.4. Installing a Slide-In Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Appendix A OIT Hardware Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Appendix B Agency Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Appendix C Dimensional Outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Appendix D OIT Panel Cutout Dimensions - Front View . . . . . . . . . . . . . . . . . . 24