STI 6200WIR8 - Manual (Page 6)

— 6 —
Mirrored Receiver Operation
The LEDs, the sounder, the siren time and the 12VDC output activation will duplicate the sensor settings enrolled on the master
RECEIVER. If a sensor is enrolled to a mirrored RECEIVER instead of the master, a transmission from the master RECEIVER will
override the mirrored RECEIVER’S LED status. To use any STI keyfob with a master + mirror RECEIVER system, enroll keyfob to
mirrored RECEIVER before adding the mirrored RECEIVER to a system.
Enrolling Mirrored (multiple) Receivers
The LEDs, the sounder, the siren time and the 12VDC output activation will duplicate the sensor settings enrolled on the master
RECEIVER. If LED “latching” is desired on the mirrored RECEIVER, this must be selected at the time of the mirrored RECEIVER’S
enrollment.
NOTE: If a SENSOR is enrolled to a mirrored RECEIVER in error (instead of the master), a transmission from the master RECEIVER
will override the mirrored RECEIVER’S LED status.
1. Check that the module is not in DELETE mode (SW7 OFF).
2. Use SW4 and SW5 to select the mirror number 1-4 if not the master (see
Component Descriptions).
3. Enrolling mirrored RECEIVERS is performed in sequential pairs:
Pair Column A Column B
1 Master => Receiver 1
2 Receiver 1 => Receiver 2
3 Receiver 2 => Receiver 3
4 Receiver 3 => Receiver 4
NOTE: All SENSORS are enrolled only to the master RECEIVER. The mirrored RECEIVERS copy the master RECEIVER’S output
(except latch settings) sequentially thru RECEIVERS 1 - 4.
4. Set SW1 and SW8 (ON) on the master RECEIVER.
5. Set SW8 (ON) on each mirrored RECEIVER.
6. Enable ENROLL mode, SW2 (ON), on the two RECEIVERS being paired together.
7. Press and release the Push Button on the Column A RECEIVER (above). The Column B receiver will give a double beep.
8. Press and release the Push Button on the Column B RECEIVER (above). The Column A RECEIVER will give a double beep.
NOTE: If Column B RECEIVER was previously enrolled to Column A RECEIVER and was not deleted, the Column A RECEIVER will
not double beep, but will work properly.
9. Disable ENROLL mode, SW2 (OFF), on both RECEIVERS.
10. Press and release the Push Button of the Column A RECEIVER (above). The LED’s of the Column B RECEIVER will light in
the same configuration.
NOTE: Keyfobs must be enrolled into each master or mirror RECEIVER where it will be used.
Keyfob Operation
An STI Keyfob can be used to remotely turn off and on the LEDs, sounder, and outputs on the STI
8-Channel Receiver and also act as a CALL or MANUAL ALERT button. While the STI 8-Channel
Receiver is turned off, it will continue to monitor the sensor signals.
To use an STI keyfob, you can separately enroll the Left/Right buttons and ON/OFF buttons to the
receiver. To use a single STI keyfob with a Master + Mirror Receiver System, enroll the keyfob to
each receiver to be used in the system before adding the Mirrored receivers to the system. To use
multiple keyfobs to independently control each receiver, enroll each keyfob to its respective receiver
before adding the Mirrored receivers to the system.
Enrolling Keyfob On/Off Buttons
Keyfob ON/OFF buttons do not enroll into zones. The keyfob ON/OFF buttons will turn on and off all 8-Channel receiver out-
puts. Cycling these buttons remotely activates the push button.
1. Check that the module is not in DELETE mode (SW7 OFF).
2. Enable ENROLL mode set (SW2 ON).
3. Press either the ON or OFF button on the keyfob.
4. The RECEIVER will give a double beep. ON/OFF keyfob buttons will not be assigned to a zone LED.
5. Repeat steps 2-4 to enroll another keyfob.
6. To exit ENROLL mode set (SW2 OFF).
NOTE: The RECEIVER will only operate with 8 keyfob Left/Right buttons enrolled into zones and 8 keyfob ON/OFF buttons
enrolled into memory. If a ninth keyfob’s ON/OFF button is enrolled, the keyfob’s ON/OFF buttons enrolled first will be deleted.
Enrolling Keyfob LEFT/RIGHT Buttons
Keyfob LEFT/RIGHT buttons enroll into a zone. The keyfob LEFT button is a CALL or MANUAL ALERT button and the RIGHT
button is a RESTORE. Follow the same steps for Enrolling Sensors into Zones and Deleting Single Zones for the Keyfob LEFT/
RIGHT buttons.
19018 ANCHOR
(4) PROVIDED
MARK AND DRILL
3/16 DIAMETER HOLES
(4) PLACES
19108 NYLON WASHER
(4) PROVIDED
19039 SCREW
(4) PROVIDED
PUSH BUTTON
19081 FRONT COVER SCREW
PUSH BUTTON SWITCH
Represents any STI 433 MHz sensor transmitting ONLY to a Master Receiver
SYSTEM 1 SYSTEM 2
MULTLIPLE SYSTEMS
Master
Receiver
Mirror #1
Receiver
Mirror #2
Receiver
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Up to
1000 ft
Master
Receiver
Mirror #1
Receiver
Master
Receiver
Mirror #1
Receiver
Mirror #2
Receiver
- Last
Mirror #2
Receiver
- Last
Monitors Housed in a
Central Office or Location
SINGLE SYSTEM
Mirror #3
Receiver
Up to
1000 ft
Mirror #4
Receiver
- Last
Up to
1000 ft
Switches (1-8) - For reference, information is also written on the
receiver case (located under Zone ID list).
1 - MIRROR MASTER OFF/ON
2 - NORMAL/ENROLL
3 - AUTO RESTORE/LATCH
4 - SIREN TIME/MIRROR#
5 - SIREN TIME/MIRROR#
6 - CHIME OFF/ON
7 - NORMAL/DELETE
8 - MIRROR SLAVE OFF/ON
SIREN
SW4 SW5 TIME MIRROR #
OFF
OFF DISABLED 1
ON OFF 30 SEC 2
OFF ON 180 SEC 3
ON ON ON CONT 4
Embossed Programming Instructions: ZONES:
LEFT BUTTON
“CALL”
RIGHT BUTTON
“RESTORE”
NO ZONE:
ON and OFF
BUTTONS
1 - MIRROR MASTER OFF/ON
2 - NORMAL/ENROLL
3 - AUTO RESTORE/LATCH
4 - SIREN TIME/MIRROR#
5 - SIREN TIME/MIRROR#
6 - CHIME OFF/ON
7 - NORMAL/DELETE
8 - MIRROR SLAVE OFF/ON
SIREN SW4 SW5 TIME MIRROR #
OFF OFF DISABLED 1 ON OFF 30 SEC 2 OFF ON 180 SEC 3 ON ON ON CONT 4
ANTENNAS
SWITCHES 1-8
ZONE LEDs
PUSH BUTTON
PIEZO
COVER
SCREW
DIPSWITCH
FUNCTIONS
WIRE ROUTE
OPTION 1
FORM C
SWITCH OUTPUTS
12V INPUTS
TERMINALS 500mA
12V OUTPUTS
TERMINALS 300mA
WIRE ROUTE
OPTION 2
TRIGGERED OUTPUT PLUG
12V , 75mA
PLUG IN ADAPTER
12V , 500mA
SURFACE FEET (x4)
(WALL MOUNTING HOLES)
EMBOSSED
INPUT AND
OUTPUTS
FCC ID: TXL34108
MODEL #34108
IC: 6335A-34108
SAFETY TECHNOLOGY INTERNATIONAL
WATERFORD, MI U.S.A.
REDDITCH, WORCESTERSHIRE UK
Tr
ig
ge
r
Ou
tp
ut
12
V
75
m
A
N
.O
.
CO
M
N
.C
.
+
1
2 V
-
I
N
50
0 m
A
30
0 m
A
PL
UG
IN
A
DA
PT
ER
12 V 500mA
ANTENNAS
SWITCHES 1-8
ZONE LEDs
PUSH BUTTON
PIEZO
COVER
SCREW
DIPSWITCH
FUNCTIONS
+
1
2 V
-
O
UT
WIRE ROUTE
OPTION 1
FORM C
SWITCH OUTPUTS
12V INPUTS
TERMINALS 500mA
12V OUTPUTS
TERMINALS 300mA
WIRE ROUTE
OPTION 2
TRIGGERED OUTPUT PLUG
12V , 75mA
PLUG IN ADAPTER
12V , 500mA
EMBOSSED
INPUT AND
OUTPUTS
FCC ID: TXL34108
MODEL #34108
IC: 6335A-34108
SAFETY TECHNOLOGY INTERNATIONAL
WATERFORD, MI U.S.A.
REDDITCH, WORCESTERSHIRE UK
Tr ig ge
r
Ou
tp ut
12
V
75
m A
N .O
.
CO
M
N .C
.
+ 1
2 V
- I N
50
0 m
A
30
0 m
A
PL UG
IN
A DA
PT
ER
12 V 500mA + 1
2 V
-
O
UT