KEPCO ABC-DM SERIES - Manual (Page 35)

ABC 040104
3-3
RESET Command Entry
Press to restore the power on default values: CV mode, output voltage = 0,
output current = minimum (1-2% of IOmax), output enabled, overvoltage
and overcurrent values per Table 1-2. Also resets overvoltage or overcur-
rent condition.
3.3.7
MENU Command Entry
Press to enter Menu commands: press repeatedly to scroll through Menu
functions: (1) set LCD contrast, (2) GPIB address, (3) Baud rate, (4) Loop
back test, (5) DCL Control, (6) Power-Up Digital DC Output on/off,
(7) Speaker on/off, (8) Calibration password, (9) previous calibration val-
ues, (10) factory calibration values, (11) view firmware serial number, (12)
set maximum voltage, (13) set maximum current, (14) protection delay.
Press ENTER or RESET to exit Menu. (1) 3.3.4,
(2) 3.5.2,
(3) 3.6.1,
(4) 3.6.4,
(5) 3.4.1,
(6) 3.3.6.1
(7) 3.3.5,
(8) 4.4, (9) 4.5,
(10) 4.6 (11) 2.8,
(12, 13) 3.3.11
(14) 3.3.10,
OV SET
7
Command Entry
Press to set overvoltage protection value. Data entry required to enter the
overvoltage protection value; press ENTER to accept displayed value. 3.3.9
Data Entry Press to enter number 7. 3.3.1.2
OC SET
8
Command Entry
Press to set overcurrent protection value. Data entry required to enter new
overcurrent protection value; press ENTER to accept displayed value. 3.3.9
Data Entry Press to enter number 8. 3.3.1.2
CALIB
9
Command Entry
Press to enter Calibration status. Requires password entry; instructions
appear on LCD. 4.3
Data Entry Press to enter number 9. 3.3.1.2
STORE Command Entry
Press to store present values of output voltage and current and overvoltage
and overcurrent protection. Data entry required to select memory location
where values are to be stored 3.3.12
EDIT
PROG
Command Entry
Press to select the starting memory location to be edited. Then use or
to view or modify the parameters of a specific memory location or to
create a new program.
3.3.14.1
STEP
4
Command Entry
Press to select starting address of program to be executed one step at a
time. 3.3.14.3
Data Entry Press to enter number 4. 3.3.1.2
TIME
5
Command Entry
Press to edit time value for specific memory location. Select memory loca-
tion (data entry), then enter time value, 0.01 to 300 seconds (data entry). 3.3.14.1
Data Entry Press to enter number 5. 3.3.1.2
RUN
6
Command Entry
Press to run a program. Requires data entry to select starting location.
Press ENTER to accept displayed value. 3.3.14.2
Data Entry Press to enter number 6. 3.3.1.2
RECALL Command Entry
Press to recall previously stored values of output voltage and current, and
overvoltage and overcurrent protection. Data entry required to select mem-
ory location containing values to be recalled; press ENTER to accept dis-
played value. 3.3.13
CLEAR Data Entry
Press to exit Data Entry status; any numbers entered are lost. Restores
Command Entry status 3.3.8
1 Data Entry Press to enter number 1. 3.3.1.2
TABLE 3-1. KEY FUNCTIONS (CONTINUED)
KEY
POWER SUPPLY
STATUS ACTIVE
DESCRIPTION
REFERENCE
PARAGRAPH