KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.38 to 2.47 - Manual (Page 151)

BOP-1K 080709
B-1
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 INTRODUCTION
This appendix defines the SCPI subsystem commands and queries used with the BOP power sup-
ply. Subsystem commands are defined in PAR. B.3 through B.146, arranged in groups as they
appear in the tree diagram, Figure 3-18. Table B-1 provides a quick reference of all SCPI subsys-
tem commands and queries used in the BOP.
TABLE B-1. SCPI SUBSYSTEM COMMAND/QUERY INDEX
COMMAND PAR. COMMAND PAR.
ABOR B.3 [SOUR:]LIST:CURR:APPL B.54
CAL B.4 [SOUR:]LIST:CURR:APPL:SWE, ? B.55, B.56
INIT[:IMM] B.5 [SOUR:]LIST:POIN? B.57
INIT:CONT, ? B.6, B.7 [SOUR:]LIST:DWEL, ? B.58, B.59
MEAS:CURR? B.8 [SOUR:]LIST:DWEL:POIN? B.60
MEAS:MODE B.9 [SOUR:]LIST:QUER, ? B.61, B.62
MEAS:VOLT? B.10 [SOUR:]LIST:REP B.63
MEAS:TRAN? B.11 [SOUR:]LIST:RES? B.64
MEM:UPD B.12 [SOUR:]LIST:SAMP:CURR B.65
OUTP[:STAT], ? B.13, B.14 [SOUR:]LIST:SAMP:VOLT B.66
OUTP:MODE, ? B.15, B.16 [SOUR:]LIST:SAMP? B.67
[SOUR:]CURR, ? B.17, B.18 [SOUR:]LIST:SET:SAMP, ? B.68, B.69
[SOUR:]CURR:LIM[:BOTH], ? B.19, B.20 [SOUR:]LIST:SET:TRIG, ? B.70, B.71
[SOUR:]CURR:LIM:NEG, ? B.21, B.22 [SOUR:]LIST:SET:WAIT, ? B.72, B.73
[SOUR:]CURR:LIM:POS, ? B.23, B.24 [SOUR:]LIST:TRIG: B.74
[SOUR:]CURR:MODE, ? B.25, B.26 [SOUR:]LIST:VOLT, ? B.75, B.76
[SOUR:]CURR:PROT[:BOTH], ? B.27, B.28 [SOUR:]LIST:VOLT:APPL B.77
[SOUR:]CURR:PROT:MODE, ? B.29, B.30 [SOUR:]LIST:VOLT:APPL:SWE, ? B.78, B.79
[SOUR:]CURR:PROT:NEG, ? B.31, B.32 [SOUR:]LIST:VOLT:POIN? B.80
[SOUR:]CURR:PROT:POS, ? B.33, B.34 [SOUR:]LIST:WAIT:HIGH B.81
[SOUR:]CURR:PROT:LIM[:BOTH], ? B.35, B.36 [SOUR:]LIST:WAIT:LEDG B.82
[SOUR:]CURR:PROT:LIM:NEG, ? B.37, B.38 [SOUR:]LIST:WAIT:LOW B.83
[SOUR:]CURR:PROT:LIM:POS, ? B.39, B.40 [SOUR:]VOLT, ? B.84, B.85
[SOUR:]CURR:TRIG, ? B.41, B.42 [SOUR:]VOLT:LIM[:BOTH], ? B.86, B.87
[SOUR:]FUNC:MODE, ? B.43, B.44 [SOUR:]VOLT:LIM:NEG, ? B.88, B.89
[SOUR:]FUNC:MODE:TRIG, ? B.45, B.46 [SOUR:]VOLT:LIM:POS, ? B.90, B.91
[SOUR:]LIST:CLE B.47 [SOUR:]VOLT:MODE, ? B.92, B.93
[SOUR:]LIST:COUN, ? B.48, B.49 [SOUR:]VOLT:PROT[:BOTH], ? B.94, B.95
[SOUR:]LIST:COUN:SKIP, ? B.50, B.51 [SOUR:]VOLT:PROT:MODE, ? B.96, B.97
[SOUR:]LIST:CURR, ? B.52, B.53 [SOUR:]VOLT:PROT:NEG, ? B.98, B.99
NOTE: Commands listed above that are followed by “, ?“ have a related query.