KROHNE OPTIFLEX 1300C EN - Manual (Page 83)

OPERATION
6
83
OPTIFLEX 1300 C
www.krohne.com 03/2014 - 4000172306 - HB OPTIFLEX 1300 R07 en
C.4.3 20 mA Setting This gives a measurement value to
20 mA (output 2).
min-max: 2 Depends on the
output function
C.4.4 Output Range Sets the effective range of output 2
either with or without over-run
3.8…20.5 mA (NAMUR),
4…20 mA
4…20 mA
C.4.5 Error Handling This sets the behaviour of current
output 2 if an error occurs. Hold Hold Hold Hold means
that the output current stays at the
value where the error occurred. Hold Hold Hold Hold is
not available if 3.8…20.5 mA (NAMUR)
is the output range.
3.6 mA, 22 mA, Hold 22 mA
Error Handling
Delay
The time after which the current output
changes to an error value. It shows
that there is a measurement error.
This value is set in the output 1 menu.
Read only Refer to
function C.3.5
C.5 Device Setup
C.5.1 C.5.1 C.5.1 C.5.1 Display Display Display Display
Settings Settings Settings Settings
To display the information you need, To display the information you need, To display the information you need, To display the information you need,
refer to these menu items. refer to these menu items. refer to these menu items. refer to these menu items.
C.5.1.1 Language Information can be displayed in any of
the 9 languages stored in the device. If
it is necessary to change the display
quickly to English, push [    ] for 3
seconds in operator mode.
English, French, German,
Italian, Japanese, Chinese
(simplified), Portuguese,
Russian, Spanish
C.5.1.2 Display Mode The display screen status will change
after the time given in C.5.1.3. (time
delay). Disable Disable Disable Disable switches off this
functionality, Auto-Off Auto-Off Auto-Off Auto-Off switches off the
display and Default Screen Default Screen Default Screen Default Screen will show
the selected default screen. To set to
the default screen, push [    ] for 1
second in the operator mode.
Disable, Auto-Off, Default
Screen.
Disable
C.5.1.3 Time Delay The time after which the display will
switch to the status set in C.5.1.2
(Display Mode). You cannot select this
menu if C.5.1.2 (Display Mode) is set to
"Disable".
1, 3, 5, 10 minutes 1 minute
Contrast The contrast control for the display
screen. You can select a shade of gray
between light gray (level 1) and black
(level 9).
Level 1, Level 2, Level 3, Level
4, Level 5, Level 6, Level 7,
Level 8, Level 9
Level 5
C.5.1.4 Length Unit The length unit displayed in operator
mode.
m, cm, mm, inch, ft, ft-inch-
1/16inch, ft-inch-1/32inch,
Free Unit
m
C.5.1.5 Volume Unit The volume unit displayed in operator
mode.
m3, L, US gal, GB gal, ft3, bbl m3
C.5.1.6 Mass Unit The mass unit displayed in operator
mode.
Tons, Kg, US Tons, GB Tons Kg
C.5.1.7 Custom.
Length Unit
A non-standard length unit for the
conversion table. This is defined by the
supervisor.
FREE_UNIT
C.5.1.8 Custom.
Length Ratio
The conversion factor between the
length unit selected in C.5.1.4 (Length
Unit) and C.5.1.7 (Custom. Length
Unit). This ratio is a multiple of 1 mm.
min-max: 1…99999 1
C.5.1.9 Custom. Conv.
Unit
Non-standard conversion unit for the
conversion table. This is defined by the
supervisor.
FREE_UNIT
Menu
No. Function Function description Selection list Default