Clinton Electronics CE-CP12B - Manual (Page 2)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AC24V
AUX1 AUX2 CO M ALM1 ALM2 ALM3 ALM4 ALM5 ALM6 ALM7 485A 485B 485A 485B AC24V
AC220V
AC220V
CO M
JP2 JP2_2
AC24V FUSE
J1
FUSE 5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19
Outdoor B ox Model CE-PTZ
-WP24
0204201792
LM1 LM2 LM3 LM4 LM5 LM 6
LM7
85A 85B 85A 85B AC24V
OM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F AC24V
AUX1 AUX2 CO M ALM1 ALM2 ALM3 ALM4 ALM5 ALM6 ALM7 485A 485B 485A 485B AC24V
AC220V
AC220V
CO M
JP2 JP2_2
AC24V FUSE
J1
FUSE 5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F
AUX1 AUX2 CO M ALM1 ALM2 ALM3 ALM4 ALM5 ALM6 ALM7 485A 485B 485A 485B AC24V
AC220V
AC220V
CO M
JP2_2
AC24V FUSE
J1
FUSE 5X20
Outdoor Box Model CE-PTZ-WP24
0204201792
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
H&F AC24V
AUX1 AUX2 CO M ALM1 ALM2 ALM3 ALM4 ALM5 ALM6 ALM7 485A 485B 485A 485B AC24V
AC220V
AC220V
CO
M
JP2 JP2_2
AC24V FUSE
J1
FUSE 5X20
Outdoor Box
Model CE-PTZ-WP24
0204201792
7 / 16
10
3/8”-16 Lock Nut
Fender Washer
Truss or Channel Strut
1/4”-20 Lock Nut
1/4”-20 socket
head allen bolt
1/4” Washer 1/4” Washer
Min. Hole Size: 3/8”
Max. Hole Size: 5/8”
400mm Long Safety Cable
1/4”-20 Safety Cable Lock Nut
3/16” Allen Wrench
7/16” Wrench
7 /16
10
3/8”-16 Lock Nut
Fender Washer
Truss or Channel Strut
1/4”-20 Lock Nut
1/4”-20 socket
head allen bolt
1/4” Washer 1/4” Washer
Min. Hole Size: 3/8”
Max. Hole Size: 5/8”
400mm Long Safety Cable
1/4”-20 Safety Cable Lock Nut
3/16” Allen Wrench
7/16” Wrench
7 / 16
10
1/2”-13 Lock Nut
Fender Washer
Truss or Channel Strut
M4 x 8mm
VESA screw
(4 places)
M4 Lock Nut
1/4”-20 Lock Nut
M4 x 45mm
1/4”-20 x 2”
M4 Washer
1/4” Washer
1/4” Washer
M4 Washer
Pole will move in
the direction of the
tightened bolt
1/4” Lock Washer
Min. Hole Size: 1/2”
Max. Hole Size: 5/8”
Min. Steel Thickness: 1/4”
Hold lower pole section and
turn counter-clockwise to loosen
Prevent lower pole from falling by
holding lower pole section here
Secure assembly by turning collar clockwise:
hand tighten as snug as possible
CAUTION: This mount is intended for use only with the maximum weights indicated.
Use with products heavier than the maximum weights indicated may result in
instability causing possible injury. This product is intended to mount to a steel
support truss, or channel strut.
7/16”
If drilling is nec
essar
y,
U
se 7/16”
metal drill
bit t
o drill thr
ough st
eel
moun
ting sur
fac
e.
Prevent lower pole from falling by
holding lower pole section here
Thread the conduit set-screw
through the hole on the end of the
lower pole.
Conduit set-screw
1/4”-20 Lock Nut
1/4”-20 socket
head allen bolt
1/4” Washer 1/4” Washer
3/4” Conduit Set-Screw Connector
(included with Clinton Electronics pendant mount)
7/16”
If drilling is necessary,
Use 7/16” metal drill
bit to drill through steel
mounting surface.
7 / 16
10
3/8”-16 Lock Nut
Fender Washer
Truss or Channel Strut
1/4”-20 Lock Nut
1/4”-20 socket
head allen bolt
1/4” Washer
1/4” Washer
Min. Hole Size: 3/8”
Max. Hole Size: 5/8”
400mm Long Safety Cable
1/4”-20 Safety Cable Lock Nut
3/16” Allen Wrench
7/16” Wrench
7 / 16
10
3/8”-16 Lock Nut
Fender Washer
Truss or Channel Strut
1/4”-20 Lock Nut
1/4”-20 socket
head allen bolt
1/4” Washer
1/4” Washer
Min. Hole Size: 3/8”
Max. Hole Size: 5/8”
400mm Long Safety Cable
1/4”-20 Safety Cable Lock Nut
3/16” Allen Wrench
7/16” Wrench