Tuff Country 56071 - Toyota Tundra 07-14 6 lift kit - Manual (Page 3)

Hardware bag 56070NB includes:
Bag # 1
Description Quantity
516UN (5/16” unitorque nut) 12
14WA (1/4” USS flat washer) 18
SUW-916 (9/16 harden u-bolt washer) 5
916312B (9/16” x 3 1/2” bolt) 4
12WA (1/2 USS flat washer) 12
916UN (9/16” unitorque nut) 6
916214B (9/16” x 2 1/4” bolt) 2
5161B (5/16” x 1” bolt) 6
Bag # 2
Description Quantity
716112B (7/16” x 1 1/2” bolt) 10
38WA (3/8” USS flat washer) 32
716UN (7/16” unitorque nut) 20
3834STB (3/8” x 3/4” self threading bolt) 2
7165B (7/16” x 5” bolt) 2
SUW-12 (1/2” harden u-bolt washer) 2
Bag # 3
Description Quantity
78512B (7/8” x 5 1/2” bolt) 2
78WA (7/8” flat washer) 4
78UN (7/8” unitorque nut) 2
M18165B (18 mm x 165 mm bolt) 2
M18WA (18 mm flat washer) 4
M18UN (18 mm unitorque nut) 2
12312B (1/2” x 3 1/2” bolt) 4
716WA (7/16” USS flat washer) 8
12UN (1/2” unitorque nut) 4
Hardware bag 56070NB1 includes:
Description Quantity
PB2408 (poly bushing) 16
S10082 (.875” x .563” x 2.080” sleeve) 4
S10058 (.875” x .510” x 2.080” sleeve) 4
S10203 (1.000” x .485” x .750” sleeve) 2
S10204 (1.750” x .563” x .593” sleeve) 1
SPN-05 (Adel bracket) 2
BH01 (.325” x .160” x 12” breather hose) 1
BH02 (.500” x .250” x 12” breather hose) 1
1434B (1/4” x 3/4” bolt) 2
14WA (1/4” USS flat washer) 2
56070-12 (rear cross member slot washer) 4
56070-18 (brake line relocation bracket) 4
56070-19 (brake line relocation bracket) 1
56070-20 (rear ABS wiring harness bracket) 1
LUBE (poly lube pack) 2
Hardware bag 916NW includes:
Description Quantity
9/16” u-bolt high nuts 8
9/16” u-bolt harden washers 8
Hardware bag CB38 includes:
Description Quantity
CB381 (3/8” x 6” centering bolt) 2
38FN (3/8” fine nut) 2
Special note: Before installation begins, it is the
customers/installers responsibility to make sure that
all parts are on hand. If any parts are missing, please
feel free to call one of our customer service
representatives @ (801) 280-2777.
Recommended tools selection:
Cut off wheel
Sawzall
Torque wrench
Standard socket set
Standard wrench set
Metric socket set
Metric wrench set
Tape measure
Hydraulic floor jacks
Torque settings:
5/16” 15—18 ft lbs.
3/8” 28—32 ft lbs.
7/16” 30—35 ft lbs.
1/2” 65—85 ft lbs.
9/16” 85—120 ft lbs.
5/8” 95—130 ft lbs.
3/4” 100—140 ft lbs.