Red Lion PAX2S - Manual (Page 18)

18
LINE 2 PARAMETERS (LINE 2)
This section details programming for the Line 2 (Bottom Line) Display. The Input, Gross, Tare, Total, Max, Min, Setpoint, Band/Deviation values and Parameter
List A/B status can be shown on the Line 2 display. The display loops described below are used to view, reset and modify the selected display values, based on the
Line 2 Value Access setting programmed for each available value.
Main Display Loop
In the Main display loop, the selected values can be consecutively read on Line 2 by pressing the D key. A left justified 2, 3 or 4-character mnemonic indicates which
Line 2 value is currently shown. When in the Main display loop, the Function keys ! and @ perform the User functions programmed in the User Input program
section.
Parameter Display Loop and Hidden Parameter Loop
These display loops provide quick access to selected parameters that can be viewed and modified on Line 2 without having to enter Full Programming Mode. These
values include Parameter List A/B selection, Setpoints and Display Settings (color, intensity and contrast). To utilize the Parameter or Hidden Parameter display loops,
a security code (1-250) must be programmed. (See Programming Security Code at the end of this section.)
The Parameter display loop is accessed by pressing the P key. The selected Parameter display loop values can be viewed and/or changed per the Line 2 Value Access
setting programmed for each available value. The Hidden Parameter loop follows the Parameter display loop, and can only be accessed when the correct security code
is entered at the Code prompt.
dISPLY
LINE 2
ACCESS
NO
Ln2
Line 2
Value Access
FUNCt
NO
Ln2
Line 2 Function
Access
ScroLL
NO
Ln2
Line 2 Scroll
Enable/Time
UNItS
FACt
Ln2
Line 2 Units
Mnemonics
COdE
0
dSP
Programming
Security Code
Pro
dISPLY
Pro
NO
F1 F2
P
D
LINE 2 PARAMETER VALUE ACCESS
DISPLAY DESCRIPTION
NOT
VIEWED
MAIN DISPLAY LOOP
(D KEY)
PARAMETER DISPLAY
LOOP (P KEY)
HIDDEN
LOOP
LOC d-rEAd d-rSt d-Entr P-rEAd P-Entr HidE
INPUt Input X X X
GrOSS Gross (absolute) X X
tArE Tare Value X X X
tOtAL Total X X X
Hi Max Value X X X
Lo Min Value X X X
LISt Parameter List A/B X X X X X X
Snx Setpoint Value (S1-S4) * X X X X X X
bn-dn Band/Deviation X X X X X X
Color Line 1 Display Color X X X X
d-LEU Display Intensity Level X X X X
d-Cont Display Contrast Level X X X X
* Indicates multiple value entries.
LINE 2 VALUE ACCESS
NO YES
Select YES to program the Value Access setting for each available Line 2
parameter. Line 2 values can be made accessible in either the Main ( D key),
Parameter ( P key) or Hidden (P key following code entry) display loops. When
the List parameter is configured for an Entr setting, a List assignment sub-
menu will follow. Refer to Input module, User sub-menu section for a
description of the function.
Each parameter must be configured for one of the following settings. Not all
settings are available for each parameter, as shown in the Parameter Value
Access table.
SELECTION DESCRIPTION
LOC Not viewed on Line 2 Display (Factory Default Setting)
d-rEAd View in Main display loop. Cannot change or reset.
d-rSt View and reset in Main display loop.
d-Entr View and change in Main display loop
P-rEAd View in Parameter display loop. Cannot change or reset.
P-Entr View and change in Parameter display loop
HidE View and change in Hidden Parameter display loop
LINE 2 FUNCTIONS ACCESS
NO YES
Select YES to display the following list of functions that can be made
available at the end of the Parameter (P-Entr) or Hidden (HidE) display loops.
Each Line 2 Function can be programmed for LOC, P-Entr, or HidE.
The more critical and frequently used functions should be first assigned to the
User Inputs and User Function keys, however if more functions are needed than
what can be obtained with user inputs and function keys, these will provide a
means to provide that access. Refer to Input module, User sub-menu section for
a description of the function.
SELECTION DESCRIPTION
rEL Zero (tare) display
r-tArE Reset Display Tare (offset) value
bAt Store batch reading in Totalizer
r-tot Reset Totalizer
r-HI Reset Maximum value
r-LO Reset Minimum value
r-HL Reset Max and Min values
r-1 Reset Setpoint output 1
ACCESS
NO
Ln2 FUNCt
NO
Ln2