Atlas Guardian Pro MLGC240W - Manual (Page 4)

-4- 598-1094-01
TROUBLESHOOTING GUIDE
If you experience a problem with your Light Control, first follow this guide. For additional assistance write to:
Atlas Lighting Products, Inc. • Customer Service Department • P.O. Box 2348 • Burlington, NC 27216
SYMPTOM
Lights will not
come on.
Lights come on
in daylight.
Lights come on
for no apparent
reason.
POSSIBLE CAUSE
1. Light switch is turned off.
2. F l o o d l i g h t i s l o o s e o r
burned out.
3. Fuse is blown or circuit breaker
is turned off.
4. Daylight turn-off is in effect (Re-
check after dark).
5. Incorrect circuit wiring, if this is a
new installation.
6. Re-aim the sensor to cover de-
sired area.
1. Light Control may be installed in
a relatively dark location.
2. Light Control is in Test. (Set
control switch to an ON-TIME
position).
1. Light Control may be sensing
small animals or automobile traf-
fic
(Re-aim sensor).
2. Range is set too high. (Reduce
Range).
3. Dual Light Level is on.
SYMPTOM
Lights stay on
continuously.
Lights flash
on and off.
Lights flash
once, then
stay off in
Manual Mode.
POSSIBLE CAUSE
1. A flood lamp is positioned too close
to the sensor or pointed at nearby
objects that cause heat to trigger the
sensor.
(Reposition the lamp away
from the sensor or nearby objects).
2. Light Control is pointed toward a heat
source like an air vent, dryer vent, or
brightly-painted heat-reflective surface.
(Reposition sensor. Reduce Range).
3. Light Control is in Manual Mode.
(Switch to Auto.)
1. Heat or light from the lamps may be
turning the Light Control on and off.
(Reposition the lamps away from the
sensor).
2. Heat being reflected from other ob-
jects may be affecting the sensor.
(Reposition sensor).
3. Light Control is in the Test mode and
warming up. (Flashing is normal un-
der these conditions. Turn Boost off.)
4. Light may be leaking through the
floodlamp reflectors. (Make sure the
metal lamp protectors are installed).
1. Sensor is detecting its own lights
(Reposition lamps to keep area be-
low sensor relatively dark).
FIVE YEAR LIMITED WARRANTY
Atlas Lighting Products, Inc. warrants against defects in materials or workmanship for a period of five years from the date
of purchase for use, and agrees to repair or, at our option, replace a defective unit without charge for either parts or labor.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse of abuse, lack of reasonable care,
the affixing of any attachment not provided with product, alteration of any attachments factory installed, loss of parts or
subjecting the fixture to any but the specified electrical service. This warranty does not cover failure of the bulb due to
accidents, abuse, misuse, vandalism, power surges, and acts of nature such as lightning damage. No responsibility is
assumed for any special incidental or consequential damages. Damages occurring during transit are not covered by this
warranty-including UPS shipments. To obtain warranty service, mail sales receipt as proof-of-purchase, date and a brief
explanation of the nature of the defect, to the address listed below. You will receive, by mail, a Return Goods Authorization
number and full instructions for returning defective merchandise. All returned goods must be accompanied by a Return
Goods Authorization number issued by Atlas Lighting Products, Inc.
NOTE: No other warranty, written or verbal, is authorized by Atlas Lighting Products, Inc. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or
limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above
exclusion and limitations may not apply to you.
For information regarding replacement parts please write to:
Atlas Lighting Products, Inc.
Attn: Customer Service Department
P.O. Box 2348
Burlington, NC 27216