Asus T2-AE1 - Manual (Page 60)

4 - 8 4 - 8 4 - 8 4 - 8 4 - 8 C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o C h a p t e r 4 : M o t h e r b o a r d i n f o
7 . 7 . 7 . 7 . 7 . A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X 1 2 V ) A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X 1 2 V ) A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X 1 2 V ) A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X 1 2 V ) A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X 1 2 V )
These connectors are for the 20-pin and 4-pin power plugs from the
power supply unit. The plugs from the power supply unit are designed
to fit these connectors in only one orientation. Find the proper
orientation and push down firmly until the connectors completely fit.
8 . 8 . 8 . 8 . 8 . I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
The PRI_IDE connector is for the UltraATA100 IDE hard disk ribbon
cable. Connect the cable’s blue connector to the IDE connector, then
connect the gray connector to a slave device (optical drive) and the
black connector to the UltraATA100 master device (hard disk drive).
Refer to the hard disk documentation for the jumper settings.
• Pin 20 on the IDE connector is removed to match the covered hole
on the UltraATA cable connector. This prevents incorrect orientation
when you connect the cables.
• For Ultra ATA/133 IDE devices, use an 80-conductor IDE cable.
®
ATX power connectors
ATXPWR
+12V DC
GND
+12V DC
GND
ATX12V
+3.3VDC
-12.0VDC
COM
PS_ON#
COM
COM
COM
-5.0VDC
+5.0VDC
+5.0VDC
PWR_OK
+12.0VDC
+3.3VDC
+3.3VDC
COM
+5.0VDC
COM
+5.0VDC
COM
+5VSB
®
IDE connector
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PIN 1
PRI_IDE