Allstar Products Group MVP-SB - Manual (Page 12)

TURNING ON POWER TO THE
OPENER
NOTE: It is now necessary to turn on the
power in order to run the opener to test the
operation and check the limit settings. Before
doing so, ensure that all mounting hardware is
installed and has been properly tightened, that
all electrical connections are per local code
requirements, and that proper wiring practices
have been followed. Also, double-check that
all ropes have been removed from the door
and that the doorway is clear.
BASIC OPERATING PARAMETERS
Please note the following Operating Parameters which
apply to openers with Auxiliary Entrapment Protection
System (Safe Finish™ Photosystem, Installation
Instructions on Page 10) and a standard wall push
button connected. Please see page 17 for instructions
concerning the Super Station Deluxe Wall Push Button
operating parameters.
IF THE DOOR IS…
...FULLY OPEN, then pushing the standard wall Push
Button or the radio control will cause the door to begin
MOVING DOWNWARD.
...FULLY CLOSED, then pushing the wall Push
Button or the radio control will cause the door to begin
MOVING UPWARD.
...MOVING UPWARD, then pushing the wall Push
Button will cause the door to STOP. The next push of
the wall button will cause the door to begin MOVING
DOWNWARD (Alternate Action Operation).
...MOVING UPWARD, then pushing the radio control
will cause the door to STOP. The next push of the
wall button will cause the door to RESUME
UPWARD MOVEMENT (Radio Operation).
...MOVING DOWNWARD, then pushing the wall
Push Button or the radio control will cause the door to
STOP, PAUSE FOR APPROXIMATELY ONE
SECOND, AND THEN BEGIN MOVING
UPWARD.
...MOVING DOWNWARD then reaches the down
limit, the lamp will blink off for a 1/2 second then turn
back on again, remaining on for 4 minutes 30 seconds
and will then automatically turn off.
...MOVING UPWARD then reaches the open limit,
the lamp will remain on for 4 minutes 30 seconds and
will then automatically turn off.
At this time (before connecting the door arm) activate
the door operator through 2 cycles of operation to
verify proper limit function. The trolley should stop at
a minimum of 2 inches before its front edge encounters
the Stop Bolt on the rail (Closed Position) and a
minimum of 4 inches before its back edge encounters
the Stop Bolt on the opposite end of the rail (Open
Position). Leave the trolley at the Closed Position on
the rail.
12
PRE-POWER ON-
INSTALLATION CHECKLIST
Before continuing with the operation and
adjustment section, make sure that:
1. The front and rear mounts for the operator are
sound and secure and the rail is positioned
correctly above the high arc of the door, and that
the opener is positioned over the door action
centerline.
2. The Manual Release Label and cord are secure
to the Manual Release Lever and the handle is
located 6 FT above floor level. The trolley and
the release mechanism have been lubricated with
a silicone spray.
3. The standard wall push button or the Super
Station (deluxe wall push button station) is in
such a position and of such a height that it can
only be actuated by an adult of average height.
The Control Button Warning label is
prominently displayed next to the push button or
wall station.
5. All wiring is correct to codes or better. There is
ground continuity from the supply. The ground
prong on the power cord is intact.
6. All ropes have been removed from the door.
The door moves freely without binding when
raised or lowered manually. The door is
correctly balanced and lubricated. All door
hardware is secure and sound. The sensitivity
has been adjusted to minimum force for the
application.
7. The plastic envelope for this manual is attached
to the wall near the push button or wall station
and this manual is placed there for owner use
and reference.
9. On door with extension type counterbalance
springs, restraint cables have been placed
through the springs.
10. On doors with adjustable bottom edges, edges
have been locked after adjustment.
OPERATION AND ADJUSTMENT INSTRUCTIONS