Samsung SC-D383-XAP - Manual (Page 42)

38_ English 臺灣 _38
快速搜尋所要的場景（設定 ZERO MEMORY）（僅適用
於SC-D38/D385）
零記憶功能可在 Camera 和 Player 模式下操作
➥ 第 18 頁
您可以在錄影帶上標記您要返回繼續播放的點。
1. 將選擇開關設定為 TAPE。（僅適用於 SC-D385）
. 按下 MODE 按鈕以設定 Camera ( ) 或 Player
( ).
3. 在錄製前或播放期間、在您要返回的點按遙控器上
的 ZERO MEMORY 按鈕。
在顯示 zero memory ( 0:00:00 ) 指示器時、
時間代碼變成設定為 zero memory。
若您要取消零記憶功能、請再次按下 ZERO
MEMORY 按鈕。
4. 尋找零位置。
當您完成播放時、在停止模式中快進或回轉錄影
帶。錄影帶將在到達零位置時自動停止。
在完成錄製後、請按下
MODE 按鈕以設定播放
機 Player ( ) 和按下 (REW) 按鈕。錄影
帶將在到達零位置時自動停止。
5. 具有 zero memory ( ) 指示器的錄影帶計時器會
從顯示畫面上消失、同時錄影帶計數器也會變更至
時間代碼。
在下列情況下、 zero memory 模式可能自
動取消：
- 在標記有零記憶功能部分的完結處。
- 當錄影帶被彈出時。
- 當您取出電池組或移除電源時。
零記憶可能在錄影帶上的錄製具有間隔時
無法正確發揮功能。
只有在使用遙控器時才能使用零記憶功能。
•
•
•
•
•
•
•
•
•
基本錄製
SEARCHING QUICKLY FOR A DESIRED SCENE
(SETTING THE ZERO MEMORY) (SC-D382/D385 only)
The zero memory function works in both Camera
and Player modes. ➥page 18
You can mark a point on a tape that you want to
return to following playback.
1. Set the Select switch to TAPE. (SC-D385 only)
2. Press the MODE button to set Camera (
) or
Player ( ).
3. Press the ZERO MEMORY button on the remote
control before the recording or during playback at
the point where you wish to return.
The time code is changed to a tape counter that
is set to zero memory with the zero memory
( 0:00:00 ) indicator displayed.
If you want to cancel the zero memory function,
press the ZERO MEMORY button again.
4. Finding the zero position.
When you have fi nished playback, fast forward
or rewind the tape in stop mode.The tape stops
automatically when it reaches the zero position.
When you have fi nished recording, press the
MODE button to set Player ( ) and press the
(REW) button.The tape stops automatically
when it reaches the zero position.
5. The tape counter with the zero memory ( )
indicator disappears from the display and the tape
counter is changed to the time code.
In the following situations, zero memory mode
may be cancelled automatically:
- At the end of the section marked with the zero
memory function.
- When the tape is ejected.
- When you remove the battery pack or power supply.
The zero memory may not function correctly where there is a
break between recordings on the tape.
The zero memory function is available only using the remote control.
•
•
•
•
•
•
•
•
•
basic recording
BATT.
CHG
MODE TAPE CARD
16BIt S
10Sec
C.Nite 1/30
60min
0:00:30 SP STBY
16:9 Wide
(SC-D385 only)