American Dynamics MegaPower CPU ADMPCPU - Manual (Page 23)

MEGAPOWER CPU 8200-0421-02, REV. E
OPERATOR’S GUIDE 21 of 21
Function Action
55-F2
Entering this key combination implies that
you will also enter another 2-digit F2 code
combination within three seconds: 99-F2 -
System Reset or 98-F2 – Reset to Factory
Defaults
60-F2 Displays current day of week
61-F2 Sets day of week to Sunday
62-F2 Sets day of week to Monday
63-F2 Sets day of week to Tuesday
64-F2 Sets day of week to Wednesday
65-F2 Sets day of week to Thursday
66-F2 Sets day of week to Friday
67-F2 Sets day of week to Saturday
70-F2
Momentarily displays software version
number as “V - - -” in the camera title field of
the selected monitor
91-F2 Changes which unit is Active
92-F2
Writes app data (cameras selected on
keyboards and other info) to Flash. Entering
92-F2 ten seconds before a front panel reset
eliminates the need to resynchronize
cameras to monitors
93-F2
Loads the dynamically defined character set
to the BVOM
98-F2
Used in combination with 55-F2 to reset the
MPCPU to factory defaults, except the direct
port settings. This function does nothing by
itself.
99-F2
Used in combination with 55-F2 to reset the
MPCPU. This function does nothing by itself.
100-F2
Sets video loss mode to OFF for the called
camera
101-F2
Sets video loss mode to SYNC ONLY for
camera
102-F2
Sets video loss mode to VIDEO LOW for
camera
103-F2
Sets video loss mode to VIDEO MED for
camera
104-F2
Sets video loss mode to VIDEO HIGH for
camera
105-F2
Sets video loss mode automatically for
called camera
106-F2
Sets DBVL mode for all cameras
automatically and transfers settings to the
CPUs to synchronize databases
107-F2
Updates video loss mode settings of all
cameras from matrix switcher to the Video
Loss Detection module
108-F2 Clears the video loss mode for all cameras
Function Action
109-F2
Downloads video loss mode of called
camera from VLD module to matrix switcher
110-F2
Transfers video loss mode of all cameras
from VLD module to matrix switcher
120-F2 End Pattern Definition
121-F2 Define Pattern 1
122-F2 Define Pattern 2
123-F2 Define Pattern 3
130-F2 Save New Pattern
131-F2 Clear Pattern 1
132-F2 Clear Pattern 2
133-F2 Clear Pattern 3
200-F2 Frees remote PTZ slots
202-F2 Resets all Alarms
300-F2
Displays current arming code for selected
monitor
301-F2 SSI Monitor Arming (1)
302-F2 SSA Monitor Arming (1)
303-F2 SSM Monitor Arming (1)
304-F2 SHI Monitor Arming (1)
305-F2 SHA Monitor Arming (1)
306-F2 SHM Monitor Arming (1)
307-F2 BSI Monitor Arming (1)
308-F2 BSA Monitor Arming (1)
309-F2 BSM Monitor Arming (1)
310-F2 BHI Monitor Arming (1)
311-F2 BHA Monitor Arming (1)
312-F2 BHM Monitor Arming (1)
313-F2 DHI/DSI Monitor Arming (1)
314-F2 DHA/DSA Monitor Arming (1)
315-F2 DHM/DSM Monitor Arming (1)
316-F2 Disarm Monitor
317-F2 Enable Manual Override
318-F2 Disable Manual Override
998-F2 Transfer Macro from keyboard to system
999-F2 Transfer Macro from system to keyboard
Note:
(1)
For an explanation of monitor arming codes, refer to
MegaPower CPU Administrator’s Guide, Appendix I,
8200-0421-03.