Sony XAV-65 - Manual (Page 21)

21
GB
Radio reception
The stations cannot be received.
The sound is hampered by noises.
 The connection is not correct.
 Connect the REM OUT lead (blue/white striped)
or accessory power supply lead (red) to the
power supply lead of a car’s antenna (aerial)
booster (only when your car has built-in radio
antenna (aerial) in the rear/side glass).
 Check the connection of the car antenna
(aerial).
 If the auto antenna (aerial) will not extend,
check the connection of the power antenna
(aerial) control lead.
Preset tuning is not possible.
 The broadcast signal is too weak.
RDS
PTY displays [PTY not found.].
 The current station is not an RDS station.
 RDS data has not been received.
 The station does not specify the program type.
Picture
There is no picture/picture noise occurs.
 A connection has not been made correctly.
 Check the connection between this unit and
other equipment, and set the input selector of
the equipment to the source corresponding to
this unit.
 The disc is defective or dirty.
 Installation is not correct.
 Install the unit at an angle of less than 45° in a
sturdy part of the car.
 The parking cord (light green) is not connected to
the parking brake switch cord, or the parking
brake is not applied.
The picture does not fit in the screen.
 The aspect ratio is fixed on the DVD.
There is no picture/picture noise occurs in the
rear monitor.
 A source/mode which is not connected is
selected. If there is no input, no picture appears
in the rear monitor.
 The color system setting is incorrect.
 Set the color system to [PAL] or [NTSC]
according to the connected monitor (page 12).
 The picture of the rear view camera is displayed
on this unit.
 No picture appears in the rear monitor if the
picture of the rear view camera is displayed on
this unit.
Sound
There is no sound/sound skips/sound cracks.
 A connection has not been made correctly.
 Check the connection between this unit and the
connected equipment, and set the input selector
of the equipment to the source corresponding to
this unit.
 The disc is defective or dirty.
 Installation is not correct.
 Install the unit at an angle of less than 45° in a
sturdy part of the car.
 The MP3 file sampling rate is not 32, 44.1, or 48
kHz.
 The WMA file sampling rate is not 44.1 kHz.
 The MP3 file bit rate is not 48 to 192 kbps.
 The WMA file bit rate is not 48 to 192 kbps.
 The unit is in pause/reverse/fast-forward mode.
 The settings for the outputs are not made
correctly.
 The DVD output level is too low (page 11).
 The volume is too low.
 The ATT function is activated.
 The format is not supported (such as DTS).
 Check if the format is supported by this unit
(page 16).
Sound is noisy.
 Keep cords and cables away from each other.
Disc operation
The disc does not play.
 The disc is defective or dirty.
 The disc is not playable.
 The DVD is not playable due to the region code.
 The disc is not finalized (page 17).
 The disc format and file version are incompatible
with this unit (page 16, 17).
 Press  to remove the disc.
MP3/WMA/Xvid files do not play.
 Recording was not performed according to the
ISO 9660 level 1 or level 2 format or the Joliet or
Romeo expansion format (DATA CD), or the UDF
Bridge format (DATA DVD) (page 17).
 The file extension is incorrect (page 17).
 Files are not stored in MP3/WMA/Xvid format.
 If the disc contains multiple file types, only the
selected file type (audio/video) can be played.
 Select the appropriate file type using the list
(page 10).
MP3/WMA/Xvid files take longer to play than
others.
 The following discs take a longer time to start
playback.
 a disc recorded with a complicated tree
structure.
 a disc to which data can be added.