Alpine CDA-9886R - Manual (Page 19)

17
-EN
3
-3
*7
Turn the Rotary encoder to select the desired
bass level (–7~+7).
You can emphasise or weaken the bass level.
4
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass bandwidth settings adjusted for one source
are effective for all other sources (FM, MW (LW), CD, etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, Bass Level is still adjustable if an
audio processor with the Bass function is connected.
*
5
When the subwoofer mode is set to OFF, its level cannot be adjusted,
refer to “Turning Subwoofer ON/OFF” (page 18).
*
6
The function is inoperable when DEFEAT is set to ON.
* 7 The adjustment can also be made by pressing Rotary encoder
(AUDIO). Refer to “Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Auto Volume/Defeat” (page 16).
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal
preference.
1
Press SOUND SETUP to activate the Sound Setting
mode.
2
Turn the Rotary encoder to select the Treble
Adjustment mode, and then press
/ENT.
SUBW. Level* 8 Bass* 9 Treble* 9 HPF* 9
Black Out SUBW. Level
3
-1 Press BAND/TA to select the desired treble centre
frequency.
10 kHz 12.5 kHz 15 kHz 17.5 kHz 10 kHz
Emphasises the displayed treble frequency ranges.
3
-2
*10
Turn the Rotary encoder to select the desired
treble level (–7~+7).
You can emphasise or weaken the treble level.
4
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• The treble level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for all
other sources (FM, MW (LW), CD, etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, Treble Level is still adjustable if
an audio processor with the Treble function is connected.
*
8
When the subwoofer mode is set to OFF, its level cannot be adjusted,
refer to “Turning Subwoofer ON/OFF” (page 18).
*
9
The function is inoperable when DEFEAT is set to ON.
* 10 The adjustment can also be made by pressing Rotary encoder
(AUDIO). Refer to “Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Auto Volume/Defeat” (page 16).
Adjusting the High Pass Filter
The High Pass Filter on this unit can be adjusted to suit your personal
taste.
1
Press SOUND SETUP to activate the Sound Setting
mode.
2
Turn the Rotary encoder to select the High Pass
Filter (HPF) Adjustment mode, and then press
/ENT.
SUBW. Level* 11 Bass* 12 Treble* 12 HPF* 12
Black Out SUBW. Level
3
Turn the Rotary encoder to select the High Pass
Filter frequency.
OFF 80 Hz 120 Hz 160 Hz
4
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• When an external audio processor is connected, this setting cannot
be made.
*
11
When the subwoofer mode is set to OFF, its level cannot be
adjusted, refer to “Turning Subwoofer ON/OFF” (page 18).
* 12 The function is inoperable when DEFEAT is set to ON.
Setting the Bass Level
Setting the Treble Centre Frequency
Setting the Treble Level