Alpine CDA-9886R - Manual (Page 31)

29
-EN
Adjusting Sound Setting in Manual Mode
You can change these sound settings to create your own preference
when the MultEQ mode is set to MultEQ off (Manual Mode).
1
Press IMPRINT to activate the Sound menu
selection mode.
2
Turn the Rotary encoder to select the desired item,
and then press
/ENT.
Subwoofer SUBW. System *
1
SUBW. Phase *
1
SUBW. Channel *
1
Factory’s EQ TW Setup *
2
Filter Type Media Xpander MX Level * 3
EQ Mode
TCR Parameter Sound Field *
4
Black Out Subwoofer
(e.g. Select Subwoofer)
* 1 These functions are inoperable when Subwoofer is set to OFF.
*
2
This function can be operable only when PXA-H100 (sold
separately) is connected and 2.2ch (3WAY) mode is set. For details,
refer to the Owner’s Manual of PXA-H100.
*
3
This function is inoperable when Media Xpander is set to OFF.
* 4 In step 2, three sound adjustment items (Parametric EQ/Graphic EQ,
T.Correction, X-Over) can be selected in Sound Field Adjustment
mode, turn the Rotary encoder to select the desired item, and then
press
/ENT to continue to step 3.
3
Turn the Rotary encoder to change the setting,
and then press
/ENT.
(e.g. Select Subwoofer ON or Subwoofer OFF)
4
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• Media Xpander, Factory’s EQ, Parametric EQ/Graphic EQ
Adjustment, EQ Mode and MX Level Adjustment are inoperable
when Defeat is set to ON.
• Pressing /ESC returns to the previous Sound menu mode.
• If no operation is performed for 60 seconds, Sound menu mode is
cancelled.
When the subwoofer is on, you can adjust the subwoofer output level
(refer to page 16).
OFF ON (Initial setting)
When the subwoofer is on, you can select either System1 or System2
for the desired subwoofer effect.
1 (Initial setting) 2
PHASE 0° (Initial setting) PHASE 180°
The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)
or SUBWOOFER REVERSE (180°). To adjust the level, turn the
Rotary encoder.
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type.
STEREO (Initial setting) MONO
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Flat Pops Rock News Jazz&Blues
Electrical Dance Hip Hop&Rap Easy Listening
Country Classical User1 User2 User3
User4 User5 User6
• By selecting User’s 1 to 6, you can recall the stored preset number in
“Adjusting the Graphic Equalizer Curve” (page 31) or “Adjusting
the Parametric Equalizer Curve” (page 30) .
Use steps 1 to 4 to select one of the Sound menu
modes to modify. See the applicable section below for
details about the selected item.
Turning Subwoofer ON/OFF
Setting the Subwoofer System
System 1 : Subwoofer level changes according to the main
volume setting.
System 2 : Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.
Setting the Subwoofer Phase
Setting the Subwoofer Channel
(SUBW. Channel)
STEREO: Subwoofer stereo (L/R) output
MONO: Subwoofer monaural output
Equalizer Presets (Factory’s EQ)