Alpine CDE-9872RE - Manual (Page 16)

14
-EN
2
Turn the Rotary encoder (CDE-9874 Series only) or
press
and (CDE-9872 Series only) until the
desired sound is obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of
BASS and TREBLE will return to the factory defaults.
Press and hold Rotary encoder (LOUD) for at least
2 seconds to activate or deactivate the loudness mode.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
1
-1 Press and hold SOUND for at least 2 seconds to
activate the Sound Setting mode (CDE-9872 Series
only).
1
-2 Press /SOUND (CDE-9874 Series only) or SOUND
(CDE-9872 Series only) repeatedly to select the BASS
mode.
BASS TREBLE HPF BASS
2
-1 Press BAND/TA to select the desired bass centre
frequency.
80 Hz 100 Hz 200 Hz 60 Hz 80 Hz
Emphasises the displayed bass frequency ranges.
2
-2 Press SOURCE/ to select the desired bass
bandwidth.
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.
2
-3 *
1 Turn the Rotary encoder (CDE-9874 Series only)
or press and (CDE-9872 Series only) to select
the desired bass level (–7~+7).
You can emphasise or weaken the bass level.
3
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass bandwidth settings adjusted for one source
are effective for all other sources (FM, MW (LW), CD, etc.).
• The function is inoperable when DEFEAT is set to ON.
*
1
The adjustment can also be made by pressing Rotary encoder
(CDE-9874 Series only) or /AUDIO (CDE-9872 Series only).
Refer to “Adjusting Bass/Treble/Balance (Between Left and Right)/
Fader (Between Front and Rear)/Loudness/Defeat” (page 13).
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal
preference.
1
-1 Press and hold SOUND for at least 2 seconds to
activate the Sound Setting mode (CDE-9872 Series
only).
1
-2 Press /SOUND (CDE-9874 Series only) or
SOUND (CDE-9872 Series only) repeatedly to select
the TREBLE mode.
BASS TREBLE HPF BASS
2
-1 Press BAND/TA to select the desired treble centre
frequency.
10.0 kHz 12.5 kHz 15.0 kHz 17.5 kHz 10.0 kHz
Emphasises the displayed treble frequency ranges.
2
-2 *
2 Turn the Rotary encoder (CDE-9874 Series only)
or press and (CDE-9872 Series only) to select
the desired treble level (–7~+7).
You can emphasise the treble level.
3
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• The treble level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for all
other sources (FM, MW (LW), CD, etc.).
• The function is inoperable when DEFEAT is set to ON.
*
2
The adjustment can also be made by pressing Rotary encoder
(CDE-9874 Series only) or /AUDIO (CDE-9872 Series only).
Refer to “Adjusting Bass/Treble/Balance (Between Left and Right)/
Fader (Between Front and Rear)/Loudness/Defeat” (page 13).
By using Loudness on the CDE-9874
Series
Setting the Bass Centre Frequency
Setting the Bass Bandwidth
Setting the Bass Level
Setting the Treble Centre Frequency
Setting the Treble Level