Panasonic EY7950 - Manual (Page 5)

-  -
(M)
Variable speed control trigger
Betriebsschalter
Gâchette de commande de vitesse
Grilletto di controllo velocità variable
Startschakelaar variabele snelheid
Disparador del control de velocided variable
Kontroludløser for variabel hastighed
Steglös varvtalsreglerare
Hovedbryter, trinnløs
Nopeudensäätökytkin
(N)
Support handle
Zusatzgriff
Manche de support
Maniglia di sostegno
Steungreep
Mango de soporte
Hjælpehåndtag
Stödhandtag
Støttehåndtak
Tukikahva
(O)
Battery charger
Ladegerät
Chargeur de batterie
Caricabatterie
Acculader
Cargador de batería
Batterioplader
Batteriladdare
Batterilader
Akkulaturi
(P)
Battery pack cover
Akkuabdeckung
Couvercle de la batterie autonome
Coperchio pacco batteria
Accudeksel
Cubierta de batería
Akkuafdækning
Batterilock
Batteripakkedeksel
Akun kansi
Original instructions: English
Translation of the original instructions:
Other languages
This tool, as a complete unit with a battery pack,
satisfies appropriate IP Degrees of Protection
based on the IEC regulations.
Definition of IP code
IP5X: Ingress of dust is not totally prevented,
but dust shall not penetrate in a quantity to
interfere with satisfactory operation of the tool
or to impair safety (In case that the talcum
powder under 75 μm intrudes inside the tool)
IPX6: Water projected in powerful jets against
the tool from any direction shall have no
harmful effects (In case that, with a nozzle
of 12.5 mm inner diameter, approximately
100 L/min of normal temperature water is
injected to the tool for 3 minutes from 3 meter
distance)
LIMITED WARRANTY
The rating of IP56 qualifies this tool for the
minimum impact of water or dust, but not for
the assurance of performance in such condi-
tions. See Safety and Operating Instructions
for further details for proper operation.
Read “the Safety Instructions” booklet
and the following before using.
I. INTENDED USE
These tools can be used to tighten
screws in clutch mode and to drill
holes in wood and metal in drill
mode. Additionally, model EY7950
can be used to drill holes in soft
concrete and similar materials in
hammer mode.
Read the Safety Instructions booklet
and the following before using.
II. ADDITIONAL
SAFETY RULES
1) Wear ear protectors.
Exposure to noise can cause
hearing loss.
2) Use auxiliary handle supplied
with the tool.
Loss of control can cause personal
injury.
3) Hold power tools by insulated
gripping surfaces when per-
forming an operation where the
cutting tool may contact hidden
wiring; contact with a “live” wire will
make exposed metal parts of the
tool “live” and shock the operator.
4) Wear a dust mask, if the work
causes dust.
5) Be aware that this tool is always in
an operating condition, since it
does not have to be plugged into
an electrical outlet.
6) When drilling or driving into walls,
floors, etc., "live" electrical wires
may be encountered. DO NOT
TOUCH THE CHUCK OR ANY
FRONT METAL PARTS OF THE
TOOL! Hold the tool only by the
plastic handle to prevent electric
shock in case you drill or drive into
a "live" wire.
7) If the bit becomes jammed, im-
mediately turn the trigger switch
off to prevent an overload, which
can damage the battery pack or
motor.
Use reverse motion to loosen
jammed bits.
8) Do NOT operate the For-
ward/Reverse lever when the
trigger switch is on. The battery
will discharge rapidly and dam-
age to the unit may occur.
9) During charging, the charger
may become slightly warm. This
is normal. Do NOT charge the
battery for a long period.
EY7442_7450_7950(EU).indb 5 2011-3-1 11:33:56