Panasonic SCAK240 - Manual (Page 11)

11
RQT8043
RQTV0061
LANG - 5
LANG - 4
FRANÇAIS
DANSK
ENGLISH
2 Press [ 0 OPEN] for DECK 1 or [OPEN 0] for DECK 2
and insert the cassette.
Insert with the side to be played facing towards you
and the exposed tape facing down. Close the holder by
hand.
Front
side
3 Press [ 3, TAPE] to start play.
To Action
stop tape playback Press [ 7, STOP].
fast-forward and
rewind Press [ 4 / REW / ] or [ / FF / ¢].
select between
loaded decks Press [DECK 1/2] (remote control :
[PLAY MODE]).
Note:
• Tape playback is momentarily interrupted if you open the other
deck.
• Tapes exceeding 100 minutes are thin and can break or get caught
in the mechanism.
• Tape slack can get caught up in the mechanism and should be
wound up before the tape is played.
• Endless tapes can get caught up in the deck’s moving parts if used
incorrectly.
Recording Recording
Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but this
unit will not be able to record or erase them correctly.
Preparation
Wind up the leader tape so recording can begin
immediately.
1
Press [OPEN 0] for DECK 2 and insert the cassette
to be recorded.
Insert with the side to be recorded facing towards you
and the exposed tape facing down.
2
Select the source to be recorded.
Radio recording:
Tune in the station. (
\ page 12)
Disc recording:
➀ Insert the disc(s) you want to record.
Press [ 6, CD] and then [7, STOP].
➁ Prepare the desired disc recording mode.
To Action
record
programmed
tracks
Perform steps 2 to 4 in “Program play”
(
\ page 8).
Perform steps 3 to 6 in “Program play”
(
\ page 8).
By remote control only
record
specifi c
discs/tracks
1) Press [DISC] and then [1] ~ [5] to select
the disc.
Ensure disc is stopped.
2) Press [PLAY MODE] to select the desired
mode ( \ page 7).
3)
For 1-ALBUM mode and 1-SONG mode:
Press [ALBUM ( or )] to select the
album.
For 1-SONG mode:
Press [ 4, REW / ] or [¢, / FF] to
select the track.
Tape-to-tape recording:
➀ Press [ 3, TAPE] and then [7, STOP].
➁ Press [ 0 OPEN] for DECK 1 and insert the cassette
to record.
3 Press [ ¶, REC] to start recording.
Other basic operations Other basic operations
To Action
stop recording Press [ 7, STOP].
record on the other
side of the tape Turn the cassette over and press [ ¶, REC].
erase a recorded
sound 1) Press [ 3, TAPE] and then [7, STOP].
2) Insert the recorded cassette into
DECK 2. Ensure there is no cassette in
DECK 1.
3) Press [ ¶, REC].
Note:
• Changes to volume and sound adjustments quality do not affect
recording.
• You cannot open DECK 1 while recording.
• You cannot fast-forward or rewind one deck while recording with
the other.
Erasure prevention Erasure prevention
The illustration shows how to remove the tabs to prevent
recording. To record on the tape again, cover as shown.
Side A
Tab for side A Tab for side B
To re-record
Normal cassette
Adhesive tape
Cassette tape – Play and record (Continued)
RQTV0061-P_1EN.indd 11 RQTV0061-P_1EN.indd 11 12/22/05 11:27:09 AM 12/22/05 11:27:09 AM