Attwood 3570 - Manual

C
D
E
B
A
3500 Series Stainless Steel 1NM and 2NM V
ertical Mount Sidelights
LED Sidelight Pair: 3560 / 3570
1NM SIDELIGHTS (SERIES 3560) For boats up to 12 meters / 39.4 feet. Meets USCG CFR 183.810, ABYC A-16 requirements and all applicable standards as tested by Imanna Laboratories, on 4/25/2008. 1 nautical mile visibility
.
2NM SIDELIGHTS (SERIES 3570) For boats up to 50 meters / 164 feet. Meets USCG CFR 183.810, ABYC A-16 requirements and all applicable standards as tested by Imanna Laboratories, on 5/9/2008. 2 nautical mile visibility
.
REQUIRED FOR INST
ALLA
TION
• Phillips screwdriver •
Drill and bits: 3/8" (10mm) for wire clearance hole and 1/8" (3mm) for mounting holes
• Pilot 1/8" (3mm) drill for mounting screws • T
wo #8 pan head stainless steel screws (not included)
LOCA
TION
1.
Before drilling mounting hole, position sidelights on a sur
face of the gunwale or
deck where you are certain that sidelights: • Are equal distance from the bow (Figure 1) • Shine straight ahead • Shine within a 5° of horizontal when the boat is fl
oating
• The light beam is not obstructed
2.
Place lights with the light labeled red on the port (left) and the light labeled green on the starboard (right). Be sure there are no obstructions at the front or side within the light’
s ar
c of visibility (112.5° each side).
3.
Measure and mark location of wire clearance hole. At the marked location(s), make a mark for a 3/8” hole. (Figure 2). • Both mounting holes must be the same distance from the bow
.
DRILLING INSTRUCTIONS 1.
Remove the cover
. (Figure 2).
2.
Align hole beneath light base with the position you’ve marked for the wire clearance hole. Set the lamp toward the bow
.
3.
Use the light base as a template to mark locations for the mounting screw pilot holes (use two #8 stainless steel screws).
CAUTION Position holes carefully on aluminum boats so that wires do not contact the hull. 4.
Drill wire clearance hole and pilot holes for the mounting screws.
MOUNTING INSTRUCTIONS 1.
Feed wires through the hole in the deck.
2.
Insert two #8 stainless steel mounting screws through base and fasten base to the deck.
3.
Snap stainless steel cover mounting base.
NOTE:
If area below the light will not be reachable after installation, attach a suitable
length of 16-gauge red- and black-colored NON-POWERED wire that can be routed to an accessible area. Make connections according to WIRING INSTRUCTIONS below
.
WIRING INSTRUCTIONS The power supply must be 12-volt DC ONL
Y.
Use crimp-type marine-grade
connectors with suitable waterproof insulation. Protect all connections with suitable materials. NOTE:
Failure to make proper connections and fuse the light properly will void the
product warranty
.
CAUTION Polarity is important. If wiring is mis-connected the LED light will not operate. 1.
Connect wires to fused power sour
ce: (See Figure 3).
•
Connect the (-) black wire to the negative (-) wire from the 12-volt supply
.
•
Connect the (+) gray or red wire along with proper fuse and switch to the positive (+) 12-volt supply
.
• Fuse must be 1-amp.
2.
Note that navigation rules require sidelights to be operated separately from anchor lights. Use either two switches or a single switch with three positions for off/anchor/running.
A
TTWOOD LIMITED 10-YEAR W
ARRANTY
Because of the longevity of Attwood’
s LED lighting technology
, Attwood offers
a limited 10-year warranty on this LED lighting product. See Product Catalog or attwoodmarine.com for details.
SA
VE THESE INSTRUCTIONS
Form Number 69440 Rev
. A
08-05
© 2008 Attwood Corporation 1016 N. Monroe Street, Lowell, MI 49331-0260 www
.attwoodmarine.com
Figure 1 / Figura 1 Abbildung 1 / Figur 1
Figure 2 A.
Red
(Port)
B.
Green
(Starboard)
Figure 2 A.
Rouge
(bâbord)
B.
V
ert
(tribord)
Figura 2 A.
Rojo
(babor)
B.
V
erde
(estribor)
Abbildung 2 A.
Rot
(Backbord)
B.
Grün
(Steuerbord)
Figur 2 A.
Röd
(babord)
B.
Grön
(styrbord)
B
A
Figure 2 / Figura 2 Abbildung 2 / Figur 2
Figure 3 A.
Pilot
Holes
B.
Bow
Direction
C.
Base
D.
Mounting
Screw
E
. Lens
Cover
Figure 3 A.
T
rous de guidage
B.
Direction de la proue
C.
Base
D.
Vis de montage
E.
Couver
cle de la lentille
Figura 3 A.
Agujeros
guía
B.
Dirección a la proa
C.
Base
D.
T
ornillo de montaje
E.
T
apa de la lente
Abbildung 3 A.
Führungslöcher
B.
Bugrichtung
C.
Sockel
D.
Montageschrauben
E.
Linsenabdeckung
Figur 3 A.
Styrhål
B.
Stävriktning
C.
Fäste
D.
Monteringsskruv
E.
Linshölje
Figure 3 / Figura 3 Abbildung 3 / Figur 3
Figure 3 A.
1-Amp
Fuse
B.
Switch
C.
(pos)
D.
(neg)
E
.
12 V DC
F
. Green
(Starboard)
G
. Red
(Port)
Figure 3 A.
Fusible d’un ampère
B.
Interrupteur
C.
(pos.)
D.
(nég.)
E.
12 volts CC
F
. V
ert
(tribord)
G
. Rouge
(bâbord)
Figura 3 A.
Fusible de 1 amperio
B.
Interruptor
C.
(positivo)
D.
(negativo)
E.
12 V de CC
F
. V
erde
(estribor)
G
. Rojo
(babor)
Abbildung 3 A.
Sicherung 1 A
B.
Schalter
C.
(pos.)
D.
(neg.)
E.
12 V Gleichstrom (DC)
F
. Grün
(Steuerbord)
G
. Rot
(Backbord)
Figur 3 A.
1
A-säkring
B.
Br
ytare
C.
(pos)
D.
(neg)
E.
12 V DC
F
. Grön
(styrbord)
G
. Röd
(babord)
C
D
C
E
G
B
A
F