CatEye CC-TR300TW [V3] - Manual (Page 16)

ENG-31
ENG
ENG-30
M2/- M1/+
Setting the measurement unit
Change the unit (km or mile).
* Stop measurement and perform the resetting operation (page 17) before you change
the unit. Unless you perform the resetting operation, “DATA RESET” appears on
the screen, preventing from changing the unit.
1. Press the MENU button in the measurement screen to
switch to the menu top screen.
Switch to the UnIT screen using the M1/+ and M2/- buttons,
and confirm with the SSE button.
Menu top:
MENU
Changing the menu: M1/+
M2/-
Confirm:
SSE
2. Select the speed unit using the M1/+ and M2/- buttons.
km ↔ mile: M1/+
M2/-
3. Pressing the MENU button returns to the menu top screen
(UnIT screen), and confirm the change(s).
Pressing it again returns to the measurement screen.
To the menu top/measurement screen:
MENU
* After the unit is switched, the total distance measured in the past is automatically
converted to the new unit.
Total distance manual entry
You can enter any value to the total distance.
The total distance in the past can be input after formatting or to a new computer.
1. Press the MENU button in the measurement screen to
switch to the menu top screen.
Switch to the ODO InPUT screen using the M1/+ and M2/-
buttons, and confirm with the SSE button.
Menu top:
MENU
Changing the menu: M1/+
M2/-
Confirm:
SSE
2. Enter the total distance using the M1/+ and M2/- buttons,
and move digits using the SSE button.
* The total distance shall be entered with a positive value.
Increase/decrease: M1/+
M2/-
Move digits:
SSE
(or)
(or)
(or)
Current speed unit
Current total value
(Back)
(Back)
(Back)
(or)
1. Press the MENU button on the measurement screen to
switch to the menu top screen.
Switch to the SEnSOR-ID screen using the M1/+ and M2/-
buttons, and confirm with the SSE button.
Menu top:
MENU
Changing the menu: M1/+
M2/-
Confirm:
SSE
2. Select the sensor ID to be checked.
Select it from “Hr (heart rate sensor)”, “SP1 (speed sensor 1)”,
and “SP2 (speed sensor 2)” using the M1/+ and M2/- buttons.
Selecting the sensor: M1/+
M2/-
3. Check whether the heart rate sensor is worn properly when
you selected “Hr”, or whether the speed sensor is mounted
properly when you selected “SP1” or “SP2”.
4. Press the SSE button to start searching the ID.
Spin the rear wheel or crank when you selected “SP1” or
“SP2”.
When the heart rate or speed (cadence) is displayed with
“ID-OK” on the screen, synchronization is completed.
Start searching:
SSE
5. Pressing the MENU button returns to the menu top screen
(SEnSOR-ID screen), and confirm the change(s).
Pressing it again returns to the measurement screen.
To the menu top/measurement screen:
MENU
* This unit enters the search mode for 5 minutes after starting the ID synch.
While “ID-SKIP” is indicated, press the SSE button in the search mode to cancel
the ID synch, and “ID-SKIP” is displayed. Unless a sensor signal is received in 5
minutes, “ID-ERROR” is displayed.
When “ID-SKIP” or “ID-ERROR” is displayed, the ID has not been synchronized
properly. In such a case, the sensor ID retains the previous ID setup.
Be sure to check the sensor/mounting condition before you check the ID again.
* SP2 is used when a computer is commonly used for second bicycles. By synchro-
nizing the ID of the second bicycle equipped with a second speed/cadence sensor
and the computer with SP2, re-synchronizing and the computer with SP2, syn-
chronizing the ID is not required every time you move the computer between first
bike to the second bike.
(or)
(or)
(Back)
(Back)
Continue