COOK CAC - Manual (Page 3)

3
tightening socket head screw in collar.
IMPORTANT: Do not over tighten!
5. Place assembled circulator face down on a flat surface.
6. Tip pedestal assembly over, placing flattened column
end in motor yoke (or along side cast aluminum support
on oscillating circulators). Align holes and insert larger
bolt and finger tighten lock nut.
7. Insert smaller bolt through motor adjustment slot and
column end and finger tighten lock nut.
8. Stand entire unit upright by lifting at the motor end of the
column. Adjust circulator angle to desired position and
tighten larger bolt to 200-230 in. lbs. and smaller bolt to
150-160 in. lbs.
9. Place assembled pedestal and fan on a flat, level
surface. Do not place the cord under the pedestal base.
Locate assembly where cord will not be a tripping
hazard.
10. Insert the plug into a properly grounded three-prong
receptacle. The unit is now ready for operation.
Optional Open Pedestal Floor Mounting
1. Large diameter column adjusts from 3 1/2- 6 ft. circulator
heights.
2. 38” open base is heavy gauge steel for stability and
designed for ease of area cleaning.
Optional Open Pedestal Assembly Instructions
1. Insert column firmly into base cup.
2. Secure column to base by inserting the enclosed screw
through the base cup hole and tightening to 50-75 in.
lbs.
3. Adjust column to desired height and lock in position by
tightening socket head screw in collar.
NOTE: Refer to Step 5 of the previous section for
assembling the circulator head to the pedestal.
NOTE: Use only the mounting hardware which is
recommended for use on Cook Air Circulators.
Optional Suspension Bracket
1. For mounting circulators from ceiling beams or rafters.
2. Furnished with secondary support cable for use when
circulator is mounted overhead.
Optional I-Beam Mount
1. For mounting circulator from I-beams and columns.
Adjustable bracket allows omni-directional air
circulation.
2. Length can be increased by adding apiece of standard
1-1/2” threaded pipe between the I-beam mount flange
and the yoke adapter.
NOTE: Use only the mounting hardware which is
recommended for use on Cook Air Circulators.
Optional Suspension Bracket
(Refer to Figure 3)
1. The suspension bracket is designed to fit over standard
size 2” lumber and should be hung from any horizontal
member 2 x 3” or larger.
Oscillating circulators must not be used with suspen-
sion bracket.
(or support bracket) and smaller hole in the pivot bracket
and install lock nut finger tight.
6. While holding the circulator at the desired angle, tighten
the smaller diameter bolt.
7. Tighten larger bolt to 200-230 in. lbs. and smaller bolt to
150-160 in. lbs., being careful to maintain the desired
position.
8. Plug the power cord into a properly grounded three-
prong receptacle.
Pedestal Mount Assembly Instructions
Circulator head comes pre-assembled, ready for installation.
1. Remove the circulator head, base, and column
assembly from the box.
2. Secure the column assembly onto the base using the
four bolts pro-vided. Apply 35-45 in-lbs. of torque.
3. Adjust column to desired height and lock in position by
tightening socket head screw in collar.
IMPORTANT: Do not over-tighten!
4. Place assembled circulator facedown on a flat surface.
5. Tip pedestal assembly over, placing flattened column
end in motor yoke. Align holes and insert larger bolt and
finger-tighten lock nut.
6. Insert smaller bolt through motor adjustment slot and
column end and finger-tighten lock nut.
7. Stand entire unit upright by lifting at the motor end of the
column. Adjust circulator angle to desired position and
tighten larger bolt to 200-230 in. lbs. and smaller bolt
to150-160 in. lbs.
8. Place assembled pedestal and fanon a flat, level
surface. Do not place the cord under the pedestal base.
Locate assembly where cord will not be a tripping
hazard.
9. Insert the plug into a properly grounded three-prong
receptacle. The unit is now ready for operation.
NOTE: Use only the mounting hardware which is provided.
Optional Heavy Duty Floor Pedestal Mountings
(Standard on CAC-PO)
1. Large diameter column adjusts from 3 1/2- 6 ft.
circulator heights.
2. 33” round base is heavy gauge steel for stability and
ease of moving.
Optional Floor Pedestal Assembly Instructions
1. Insert column firmly into tapered cup.
2. Secure column to base by slightly moving the top of the
column by hand while exerting a downward pressure
until column is tight in tapered cup.
3. Insert enclosed screw and washer through the pedestal
base into the pedestal column and tighten to 150in. lbs.
torque securing the assembly.
4. Adjust column to desired height and lock in position by
To avoid personal injury, circulators must be supported
any time angle is adjusted.
Use only as a wall mounting for oscillating units. Do not
use as a ceiling mount.