Fagor FFK1700X - Manual (Page 15)

13
1
Instruction manual
Very important: Please read this manual fully before using your refrigerator.
This manual has been designed so that the text is linked to the relevant drawings.
Installation
Identify the model of your refrigerator (“a”, “b”,
“c”, “d”) by comparing the control panel with the
illustrations.
1.1 Unpacking. Remove all the protection.
1.2 Location. Position the refrigerator away
from heat sources and protected from direct
sunlight to reduce consumption.
Do not install the refrigerator outside or
anywhere it is exposed to rain.
Air must be able to circulate around the back
of the refrigerator. Leave 25 mm between the
back of the refrigerator and the wall behind
it. Do not block the space between your
refrigerator and the fl oor or ceiling with any
object.
Level the refrigerator to prevent any vibrations
or noise. Remember that if the refrigerator
is located next to a wall or cabinet, it might
make a small noise.
Also check that the shelves have been fi tted
correctly, and place containers apart to
prevent any vibrations.
1.3 Electrical connection. Stand the refrigerator
upright for at least 2 hours before plugging it
in. Check the information on the specifi cations
plate (220-240V earthed) (1.3.1, 1.3.2).
Do not use any adapters or extension leads.
Make sure that the lead is not touching the
motor or trapped underneath it.
1.4 Changing the direction the door opens.
Unplug the refrigerator from the mains supply
and empty it completely.
Gently lay the appliance on its back (1.4.1).
Undo the screws (1.4.2) and remove the top
hinge and the rotating bushing with the aid of
a screwdriver (1.4.3).
0
Identifi cation
e n g l i s h
Unplug by pressing on the connector tab
(1.4.4). Remove the refrigerator door (1.4.5).
Remove the control panel, levering it up
by inserting a screwdriver in the notches
provided for that purpose (1.4.6).
Make a notch for the lead on the other side,
in the area indicated on the casing (1.4.7).
Replace the control panel passing the lead
through the notch made (1.4.8).
Undo the screws from the bottom hinge and
remove it. Change the position of the pin in
the hinge and position it on the other side
(1.4.9).
Remove the vertical handle and fi t it on the
other side of the door turning it 180º (1.4.10).
Fit the door (1.4.11).
Fit the closing capsule in the top hinge
space on the other side (1.14.12). Press the
connector to plug it into the door (1.4.13).
Fit the top hinge and the rotating bushing,
inserting any spare lead in the control panel
(1.4.14) and replace the screws (1.4.15).
Lift the refrigerator up carefully (1.4.16).
1.5 Levelling the appliance. Adjust the feet so
that it is tilting backwards slightly, to help the
door close correctly (1.5.1).
2.1 Switching on the refrigerator. Press the
button (2.1.1) or (2.1.2). Press , until
a digit appears on the display (2.1.3) or turn
the control (2.1.4). In models
c and
, the “on” LED will come on to indicate that
the appliance is switched on.
The child lock is automatically activated in
model
a , to release it press the button
for 3 seconds (2.3.10). Models b , c
and do not have the automatic lock
function.
2.2 Setting the temperature. Press the
, buttons (2.2.1, 2.2.2). Press ,
(2.2.3), or turn the control (2.2.4). Once
you have set the temperature required,
you can fi nd out the actual temperature by
pressing the
or (2.2.5, 2.2.6),
2
Use