Silverline Clean Water Pump 2 - Manual (Page 7)

6
GB
Remove adjusting keys
• Where adjusting keys exist, ensure they are removed prior to using the
tool. Always check to see that keys and adjusting devices are removed
from the tool before use
Clean the work area
• Accidents can occur where benches and work areas are cluttered or
dirty. Keep floors clear and avoid working where the floor is slippery. If
working outdoors, be aware of all potential slip and trip hazards before
using this tool
Trained, competent persons
• This tool should be used by trained, competent persons only
Children and pets
• Keep children and pets at a safe distance from the work area. Lock tools
away where children cannot gain access
Use the correct tool
• Do not force or attempt to use a tool for a purpose for which it was not
designed. This tool is not intended for industrial use
Wear suitable clothing and footwear
• Do not wear loose fitting clothing, neckties, jewellery, or other
items which may become caught. Wear non-slip footwear or, where
appropriate, footwear with protective toe caps. Long hair should be
covered or tied back
Keep your balance
• Do not over-reach. Keep proper footing at all times and do not use tools
when standing on an unstable surface
Accessories
• The use of any attachment or accessory, other than those mentioned in
this manual, could be dangerous and result in damage or injury, and may
invalidate your warranty
Never stand on your tool
• Standing on your tool or its stand could cause serious injury if the tool is
tipped or collapses. Do not store materials above or close to the tool in such
a way that a person might stand on the tool to reach the stored items
Secure work
• Where possible, always secure work. If appropriate, use a clamp or vice
so that both hands are free to operate the tool
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing.
Carefully check that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre.
DO NOT USE IF DEFECTIVE
Internal Combustion Safety
Dangerous environment
• Do not use petrol tools in damp or wet conditions, or expose them to
rain. Provide adequate surrounding work space and keep area well lit.
Do not use petrol tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gases, or dust of an
explosive nature
Protect yourself from vibration
• Hand held tools may produce vibration. Vibration can cause disease.
Gloves to keep the operator warm may help to maintain good blood
circulation in the fingers. Hand held tools should not be used for long
periods without a break
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 80dB.
It is the responsibility of the user to ensure that other people near to
where the tool is to be used are also suitably protected
Switch off before connecting
• Ensure that the engine is stopped before connecting any accessories to
the tool. If the tool stops unexpectedly make sure that the engine is not
running before attempting to check the tool
Specification
Engine: ........................................ 4 stroke OHC
Power: ........................................ 6.5hp
Fuel: ............................................ Unleaded
Oil type: ...................................... 10W-30
Oil Qty: ....................................... 0.6L
Spark plug: .................................. Torch F6TC, Champion
N9YC or equivalent
Spark plug gap:........................... 0.5 – 0.7mm
Fuel tank capacity: ...................... 3.6L
Max continuous run time: ........... 14H
Maximum pump rate:.................. 27m
3 /h
Pumping elevation: ..................... 30m
Suction head ............................... 7m
Suction hose (reinforced) ............ 50mm diameter
Discharge hose ........................... 50mm diameter
Sound Level ................................ 99dB(A)
The sound intensity level for the operator may exceed
85dB(A) and sound protection measures are necessary.
As part of our ongoing product development, specifications
of Silverline products may alter without notice.
General Safety
Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
Keep guards in position
• Where guards exist keep them in position, in good working order,
correctly adjusted and aligned. Never attempt to use a tool if any of
the supplied guards are missing. If any guards are damaged, replace
before use
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
Do not use petrol tools where there is a risk of explosion or
fire from combustible material, flammable liquids, flammable
gases, or dust of an explosive nature
If the engine has been running it will be very hot.
DO NOT
TOUCH.
Exhaust gases contain carbon monoxide, a toxic gas. Exposure
to it can provoke loss of consciousness and even death.
Conforms to relevant legislation and safety standards.
996985_Z1MANPRO1.indd 4 27/06/2011 12:29