Silverline 1010W Hammer Drill - Manual (Page 6)

www.silverlinetools.com
5
1010W Hammer Drill 129901
1 Chuck
2 Gear Selection Switch
3 Hammer Selection Switch
4 Forward/Reverse Selector
5 Lock On Button
6 On/Off Switch
7 Speed Control Dial
8 Side Handle
9 Depth Gauge
Product Familiarisation
Unpacking Your Tool
• Carefully unpack and inspect your power drill. Fully familiarise yourself
with all features/functions of the tool
• Ensure that all parts of your power drill are present and in good condition.
If any part is missing, or damaged, have such parts replaced before
attempting to use this tool
Operating Instructions
Side handle
• The Side Handle (8) should always be used when drilling
• Always hold the drill firmly using both hands
• The side handle can be adjusted to best suit the work to be performed
• To adjust the side handle, rotate the handle grip anti-clockwise, this
will loosen the handle assembly. Move the side handle to the required
position, and secure by rotating the handle grip clockwise
Operating the chuck
• The Chuck (1) can be opened by holding the rear chuck ring, and rotating
the front chuck ring anti-clockwise
• To tighten the chuck, hold the rear chuck ring, and rotate the front chuck
ring clockwise
• Do not run the drill to tighten or release the chuck. Doing this will cause
permanent damage to your tool
On/off switch
• To start the drill, squeeze the On/Off Switch (6)
• To stop the drill, release the On/Off Switch (6)
Lock on button
• The drill is equipped with a Lock On Button (5). This allows the on/off
switch to be locked into the ‘on’ position for tasks that require extended
continuous running
• To use the lock on function, depress the lock on button whilst squeezing
the on/off switch. The on/off switch can then be released and the drill
will continue to run
• To stop the drill, squeeze, then release the on/off switch
Speed control
• The speed of the drill can be varied between 0 and 1000min -1 (low gear),
or 0 and 3000min -1 (high gear)
• Rotate Speed Control Dial (7) to adjust the speed
Direction Control
• The direction of the drill can be changed using the Forward/Reverse
Selector (4)
• To run the drill in a clockwise direction, push the forward/reverse selector
to the right
Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may
affect the power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly
maintained power tools
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous
situation
Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained
Additional Safety for Hammer
Drills
For safety relating to protective clothing/equipment and general health
hazards relating to power tools; refer to General and Electrical Safety
sections in this manual
Important: It is imperative to follow all national safety regulations
concerning installation, operation and maintenance
• Do not allow anyone under the age of 18 years to use this tool, and
ensure that operators are qualified and familiar with the operating and
safety instructions
• When using the drill, use safety equipment including safety glasses or
shield, ear defenders, and protective clothing including safety gloves.
Wear a dust mask if the drilling operation creates dust
• Use metal and voltage detectors to locate concealed electric, water or
gas lines. Avoid touching live components or conductors
• Extension cable reels used with this tool must be completely unwound.
Minimum conductor cross section: 1.0mm2
• When using this tool outdoors, connect to a power supply with an RCD
device and minimum 1.5mm2 extension cable with water protected
plugs in good working order
• Ensure that the chisel or drill bit is securely fixed in the chuck. Insecure
drill bits can be ejected from the machine causing a hazard
• Ensure that the lighting is adequate
• Ensure that the drill bit is in contact with the workpiece prior to starting
up the tool
• Before drilling, check that there is sufficient clearance for the drill bit
under the workpiece
• Use both hands when operating this tool
• Use auxiliary handles supplied with the tool
• Do not put pressure on the tool, to do so would shorten its service life
• Drill bits get hot during operation, allow to cool prior to handling them
• Never use your hands to remove sawdust, chips or waste close by the bit
• If you are interrupted when operating the drill, complete the process and
switch off before looking up
• Where possible, use clamps or a vice to hold your work
• Always disconnect the hammer drill from the electric supply before
changing a chisel or drill bit
• Examine the chuck regularly for signs of wear or damage. Have damaged
parts repaired by a qualified service centre
• Always wait until the drill has come to a complete stop before putting
it down
• On completion of the work, disconnect the tool from the power source
and remove chisel/bit from the machine
• Periodically check all nuts, bolts and other fixings and tighten where
necessary
129901_Z1MANPRO1.indd 5 10/05/2012 16:21