ConTech Lighting CGL12 - Manual

For Con-Tech Lighting 12" LED Decorative Pendant Series: CGL12
CGL12 INST www.contechlighting.com All specifications subject to change without notice. 1-847-559-5500 This document can be recycled.
Continued on Page 2
1
Knurled Cap Nut
Knurled Standoff
Heat Sink
and Leg
Assembly
Bottom Glass
Bottom Ring
SHADE INSTALLATION:
Open carton and remove the canopy driver compartment and set
aside. Remove heatsink/leg assembly from carton and carefully set
aside. Placing upright on four (4) legs to avoid scratching or damag-
ing heatsink/leg assembly is recommended. Remove styrofoam
packing insert from the bottom of the carton and place on table or
work surface. Carefully place heatsink/leg assembly upside down
on styrofoam packing insert to facilitate shade installation. (Figure 1)
Place the aluminum, acrylic or glass shade within the four mounting
legs. Position bottom ring in place and align four (4) holes. Thread and
tighten four (4) 3mm hex socket head screws. (Figure 1)
BOTTOM GLASS INSTALLATION:
Thread four (4) knurled standoffs into the bottom ring. Unpack the
bottom floating glass and attach (frosted side towards LED) to the
bottom ring of the frame by aligning the four (4) holes with the four
(4) knurled standoffs. Lock the glass in place with the (4) knurled
cap nuts and carefully tighten. (Figure 1)
FLEXIBLE CORD INSTALLATION:
To adjust the flexible cord length, remove the four (4) screws from
the top of the canopy (Figure 2) and disconnect the red, black and
green driver wires.
Determine the length of exposed flexible cord required. If cutting is
required, loosen the coiled 18-3 cable. Leave only 6-8" for wiring
available. Mark the cable where it needs to be cut. Carefully score
the outer jacket around the diameter of the cable about 6-8" below
the total length. Score the outer jacket lengthwise for that 6-8"
section. Use proper rotary cable slitters such as Ideal #45-128 or
Eclipse #200-009. Remove the outer jacket. Trim off the individual
wire insulation leaving 1/2" bare wire exposed.
Install the internal two-piece cable strain relief. Tighten the two (2)
3mm hex socket head screws in order to hold the cord to the
driver housing/canopy safely (Figure 3).
Reconnect the LED driver to the flexible cable. Connect red to
black, black to white and green to green ground wires. (Figure 4)
Once the flexible cable length is set, adjust the length of the aircraft
cable to match by pulling the excess cable through the canopy. Once
the length is properly adjusted, the excess cable can be coiled and
left in the canopy or may be cut. Prior to cutting cable, the brass
cable retainer must be repositioned. Loosen retaining screw with
Philips head screwdriver, reposition the retainer approximately 1" –
2" from the canopy and retighten the retaining screw. Proceed with
cutting of aircraft cable using proper aircraft cable cutting tools.
Reattach the top of the canopy with the four (4) screws.
There should not be any excess flexible cord in the driver
compartment/top mounting canopy. Per UL1598 and NEC 300.14,
“at least 150mm (6in.) of free conductors and less than 8in., measure
from the point in the box where it emerges from its raceway or cable
sheath shall be left at each outlet, junction and switch point for splices
or the connector of luminaires or devices”.
RIGID STEM INSTALLATION:
For Rigid Stem installation, remove the four (4) screws from the top
of the canopy (Figure 2) and disconnect the red, black and green
driver output wires. The canopy with swivel is designed for sloped
ceiling applications. Determine the length of the stem with external
couplings required.
Loosen the two (2) 3.0mm steel hex socket head screws from the
cable connector. Remove the inner grommet. Slide the stems over
the flexible cord and screw the rigid stem into the cable connector
and tighten the two (2) 3.0mm steel hex socket head screws.
Determine the length of flexible cord required, and follow the flexible
cord installation instructions for the balance of the installation.
Shade
Styrofoam
Packing
Insert
Hex Screw
Top of Canopy
(4) Brass Screws
on Ballast Plate
Mounting Bar
There should not be any excess cable in the ballast
compartment. Leave only 6-8" for wiring available.
Mono-Point Canopy
Cord Grip Connector
(2) Hex Screws