Anritsu MG3690A - Manual (Page 14)

14
Ordering Information
Models
MG3691A 2 – 8.4 GHz Signal Generator
MG3692A 2 – 20 GHz Signal Generator
MG3693A 2 – 30 GHz Signal Generator
MG3694A 2 – 40 GHz Signal Generator
MG3695A 2 – 50 GHz Signal Generator
MG3696A 2 – 65 GHz Signal Generator
Options and Accessories
MG3690A/1A Rack Mount with slides – Rack mount kit containing a set of track slides (90 degree tilt capability), mounting ears,
and front panel handles to let the instrument be mounted in a standard 19-inch equipment rack.
MG3690A/1B Rack Mount without slides – Modifies rack mounting hardware to install unit in a console that has mounting
shelves. Includes mounting ears and front panel handles.
MG3690A/2X Mechanical Step Attenuator – Adds a 10 dB/step attenuator. Rated RF output power is reduced. (This option
comes in different versions, based on instrument configuration.)
MG3690A/2E Electronic Step Attenuator – Adds a 10 dB/step electronic attenuator with a 120 dB range for the MG3691A.
Rated RF output power is reduced. (Not available with Option 20 or 22.)
MG3690A/3 Ultra Low Phase Noise, main band – Adds new modules to significantly reduce SSB phase noise.
MG3690A/4 10 MHz to 2.2 GHz RF coverage, Ultra-Low Phase Noise version – Uses a digital down converter to significantly
reduce SSB phase noise.
MG3690A/5 10 MHz to 2 GHz RF coverage – Uses an analog down converter.
MG3690A/6 Analog Sweep Capability – (limited to ≥ 500 MHz when used with Option 4.)
MG3690A/7 IF Up-Conversion – Adds an internal 40 GHz mixer for up-converting an IF signal. (Not available with MG3695A,
MG3696A, or with Options 18 or 20.)
MG3690A/8 Power Monitor – Adds internal power measurement capability. (Not available with Option 9.)
MG3690A/9X Rear Panel Output – Moves the RF output connector to the rear panel. (This option comes in different versions,
based on instrument configuration.) (Not available with Option 8.)
MG3690A/10 User-Defined Modulation Waveform Software – External software package provides the ability to download
user-defined waveforms into the memory of the internal waveform generator, serially or via GPIB. External PC
and an instrument with LF Generator, Option 23, are required.
MG3690A/12 Frequency and Phase Modulation – External, via a rear panel BNC connector. For internal modulation capability,
requires additionally LF Generator, Option 23.
MG3690A/13X Pulse Modulation – External, via a rear panel BNC connector. For internal modulation capability, requires additionally
Pulse Generator, Option 24. (This option comes in different versions, based on instrument configuration.)
MG3690A/14 Amplitude Modulation – External, via a rear panel BNC connector. For internal modulation capability, requires
additionally LF Generator, Option 23.
MG3690A/15X High Power – Adds high-power RF components to the instrument to increase its output power level. (This option
comes in different versions, based on instrument configuration.)
MG3690A/16 High Stability Time Base – Adds an ovenized, 10 MHz crystal oscillator as a high-stability time base.
MG3690A/17 Delete Front Panel – Deletes the front panel for use in remote control applications where a front panel display
and keyboard control are not needed. (Only available with Options 1A or 1B)
MG3690A/18 mmW Bias Output – Adds a rear panel BNC Twinax connector required to bias the 5400-xWRxx millimeter wave
source modules, sold separately. (Not available with Option 7.)
MG3690A/20 Scan Modulation – Adds an internal Scan modulator for simulating high-depth amplitude modulated signals.
Requires an external modulating signal input capability. (Not available on models MG3693A, MG3694A, MG3695A,
MG3696A, or with Options 2E, 7, or 22.)
MG3690A/22 0.1 Hz to 10 MHz Audio coverage – Uses a DDS for coverage down to approximately DC. When adding Option
22, the output power is derated by 2 dB. The frequency resolution below 10 MHz is 0.02 Hz. No modulation is
available in the 0.1 Hz to 10 MHz band. (Not available without Option 4 or 5, or with Option 20 or 2E)
MG3690A/23 LF Generator – Provides modulation waveforms for internal AM, FM, or Φ M. (Not available without Option 12 or 14.)
MG3690A/24 Pulse Generator – Provides pulse waveforms for internal Pulse Modulation. (Not available without Option 13.)
MG3690A/25X Analog Modulation Suite – For ease of ordering and package pricing, this option bundles Options 12, 13, 14, 23
and 24, offering internal and external AM, FM,
Φ M, and Pulse Modulation. (This option comes in different versions,
based on instrument configuration.)