Anritsu MG3690A - Manual (Page 9)

9
1 2.2 GHz with Option 4, DDC.
2 For 50 and 65 GHz units, overshoot >40 GHz is 20% typical at rated power.
3 Period must be longer than the sum of delay and width by 5 clock cycles
minimum.
* Typical
≥ 10 to
<31.25 MHz 400 ns* 33%* 40 ns* ±70 mV*
(Opt. 4)
≥ 31.25 to
<125 MHz 90 ns* 22%* 12 ns* ±130 mV*
(Opt. 4)
≥ 125 to
<500 MHz 33 ns* 11%* 12 ns* ±70 mV*
(Opt. 4)
≥ 500 to
<2200 MHz 15 ns 10% 12 ns* ±15 mV*
(Opt. 4)
≥ 10 to 15 ns
<1000 MHz 10 ns* 10% 8 ns* ±15 mV*
(Opt. 5)
≥
1 to 10 ns
<2 GHz 5 ns* 10% 8 ns* ±15 mV*
(Opt. 5)
≥ 2 to 10 ns
≤
65 GHz 5 ns* 10%
2
8 ns* ±10 mV*
Frequency
Range
Rise & Fall
Time
(10% to 90%)
Overshoot
Pulse Width
Compression
Video
Feedthrough
Amplitude Modulation (Option 14)
All amplitude modulation specifications apply at 50% depth, 1 kHz
rate, with RF level set 6 dB below maximum specified leveled
output power, unless otherwise noted. Amplitude Modulation is not
available <10 MHz with Option 22.
AM Depth (typical): 0-90% linear; 20 dB log
AM Bandwidth (3 dB):
DC to 50 kHz minimum
DC to 100 kHz typical
Flatness (DC to 10 kHz rates): ±0.3 dB
Accuracy: ±5%
Distortion: <5% typical
Incidental Phase Modulation (30% depth, 10 kHz rate):
<0.2 radians typical
External AM Input: Log AM or Linear AM input, rear-panel BNC,
50 Ω input impedance. For internal modulation, add LF Generator
Option 23.
Sensitivity:
Log AM: Continuously variable from 0 dB per volt to
25 dB per volt.
Linear AM: Continuously variable from 0% per volt
to 100% per volt.
Maximum Input: ±1V
LF Generator (Option 23)
Two internal waveform generators are added, one providing
a frequency or phase modulating signal and the other an amplitude
modulating signal. This Low Frequency (LF) Generator option can
only be ordered in combination with either FM/
Φ M or AM options,
12 and 14 respectively.
Waveforms: Sinusoid, square-wave, triangle, positive ramp,
negative ramp, Gaussian noise, uniform noise. (Check Option 10
for User-Defined)
Rate:
0.1 Hz to 1 MHz sinusoidal
0.1 Hz to 100 kHz square-wave, triangle, ramps
Resolution: 0.1 Hz
Accuracy: Same as instrument timebase
Output: Two BNC connectors on the rear panel, FM/ Φ M OUT and
AM OUT
External Input: Rear-panel BNC. For internal modulation, add Pulse
Generator Option 24.
Drive Level: TTL compatible input
Input Logic: Positive-true or negative-true, selectable from
modulation menu.
Pulse Generator (Option 24)
Modes: Free-run, triggered, gated, delayed, singlet, doublet, triplet,
quadruplet.
Accuracy: 10 ns (5 ns typical)
Inputs/Outputs: Video pulse and sync out, rear-panel
BNC connectors
Pulse Generator option is not available without Pulse Modulation
Option 13.
Pulse Width 25 ns to 419 ms 100 ns to 1.6 s
Pulse Period 3 250 ns to 419 ms 600 ns to 1.6s
Variable Delay
Singlet 0 to 419 ms 0 to 1.6 s
Doublet 100 ns to 419 ms 300 ns to 1.6 s
Triplet 100 ns to 419 ms 300 ns to 1.6 s
Quadruplet 100 ns to 419 ms 300 ns to 1.6 s
Resolution 25 ns 100 ns
Parameter Selectable Clock Rate
40 MHz 10 MHz
External Pulse Modulation (Option 13)
Pulse modulation specifications apply at maximum rated power,
unless otherwise noted. Pulse modulation is not available <10 MHz
with Option 22.
On/Off Ratio: >80 dB
Minimum Leveled Pulse Width:
100 ns, ≥ 2 GHz 1
1 µs, <2 GHz 1
Minimum Unleveled Pulse Width: <10 ns
Level Accuracy Relative to CW (100 Hz to 1 MHz PRF):
±0.5 dB,
≥
1 µs pulse width
±1.0 dB, <1 µs pulse width
Pulse Delay (typical): 50 ns in External Mode
PRF Range:
DC to 10 MHz, unleveled
100 Hz to 5 MHz, leveled