Asus A8R-MVP - Manual (Page 44)

2 - 2 2 2 - 2 2 2 - 2 2 2 - 2 2 2 - 2 2 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] ,
( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ r e d ] , S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] ,
S A T A 4 [ b l a c k ] )
S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can can create a
RAID 0, RAID 1, RAID 0+1, RAID 5, and JBOD configuration. Refer to
Chapter 5 for information on creating a RAID configuration.
Enable the S e r i a l A T A C o n t r o l l e r S e r i a l A T A C o n t r o l l e r S e r i a l A T A C o n t r o l l e r S e r i a l A T A C o n t r o l l e r S e r i a l A T A C o n t r o l l e r and O n b o a r d S A T A B o o t R O M O n b o a r d S A T A B o o t R O M O n b o a r d S A T A B o o t R O M O n b o a r d S A T A B o o t R O M O n b o a r d S A T A B o o t R O M
items in the BIOS if you want to use the Serial ATA RAID feature. See
section “4.3.5 Storage Configuration” for details.
• Plug your Serial ATA boot disk on the master port (SATA1/2 to
support S3 function).
• Install the Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack1 or later when using Serial ATA.
A8R-MVP
®
A8R-MVP IDE connectors
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PRI_IDE
PIN 1
SEC_IDE
A8R-MVP
®
A8R-MVP SATA connectors
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA4
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
SATA3
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND