Arcam AVR surround amplifier / AV processor AVR600 - Manual (Page 35)

E-33
English
SAT SaT device Mode
The z Device Mode button configures the CR102
to control the functions of a satellite receiver. You will
need to configure this Device Mode to work with your
equipment. Pressing this button also selects SAT as the
AVR500/AVR600/AV888 source.
P Toggles power between standby and on
0 … 9 Functions as original remote number key.
PHONO
E
Selects TApE input on the AVR500/AVR600/
AV888.
ShiFT + E selects phono input on the
AVR500/AVR600/AV888.
TV/AV
r
Toggles between the available inputs on
your satellite receiver
S Modifies many keys (see individual key
descriptions, below)
AUX
H
Selects multichannel ( MCh ) input on the
AVR500/AVR600/AV888.
ShiFT + H selects AuX input on the
AVR500/AVR600/AV888.
NET
e
Selects ipoD input on the AVR500/AVR600/
AV888
ShiFT + e selects network ( nET ) internal
input on the AVR500/AVR600/AV888
OK
Navigate menus.
oK confirms a setting (equivalent to ‘Enter’
or ‘Select’ on some remotes).
M Controls Backup function, if available.
U Performs same function as on original
remote, if available.
D On some Satellite and Cable set top boxes
this key functions as the Guide key to open
the EPG (Electronic Program Guide).
@
Toggles the mute function.
By default this key operates the AVR500/
AVR600/AV888 Mute
]
Channel down
[
Channel up
- + Decrease ( – ) and increase ( + ) AVR500/
AVR600/AV888 volume
) Fast rewind
$ Starts the playback
& Toggles pause of playback
( Fast forward
!
(not used)
#
Stop playback
%
Start recording
h
(not used)
u
(RED)
Duplicates function of RED key for some
Satellite and Cable set-top boxes
t
(GREEN)
Duplicates function of gREEn key for some
Satellite and Cable set-top boxes
o
(yELLOw)
Duplicates function of yEllow key for some
Satellite and Cable set-top boxes
b
(BLUE)
Duplicates function of BluE key for some
Satellite and Cable set-top boxes
AV aV device Mode
The a Device Mode button configures the CR102 to
control the functions of a television or other display
device. You will need to configure this Device Mode to
work with your equipment. Pressing this button also
selects AV as the AVR500/AVR600/AV888 source.
P
Toggles power between standby and on.
(Some TVs require you to use a number
key to turn them on.)
0 … 9 Functions as original remote number key –
usually for channel selection.
PHONO
E
Selects Tape input on the AVR500/
AVR600/AV888.
ShiFT + E selects phono input on the
AVR600/AV888.
TV/AV
r
Toggles between the available inputs on
your display device (e.g. TV/AV)
S
Modifies many keys (see individual key
descriptions, below)
AUX
H
Selects multichannel ( MCh ) input on the
AVR500/AVR600/AV888.
ShiFT + H selects AuX input on the
AVR500/AVR600/AV888.
OK
Navigate setup and programme selection
menus.
oK confirms a selection (equivalent to
‘Enter’ or ‘Select’ on some remotes).
M EXiT function on some models.
U Functions as original remote key, if
available.
D
Display INFO or OSD (On Screen Display)
function, if available.
@ Toggles the mute function.
By default this key operates the AVR500/
AVR600/AV888 Mute
] Channel down
[ Channel up
- +
Decrease ( – ) and increase ( + ) AVR500/
AVR600/AV888 volume.
)
Toggles TEXT page on/off
$ TEXT page off
& Turns Programme-In-Programme (PIP)
on, if available
(
Activates PIP move, if available
!
Activates PIP swap, if available
#
Activates PIP freeze, if available
%
Activates PIP channel up, if available
h Activates PIP channel down, if available
u
(RED)
Duplicates function of RED key for Text TV
t
(GREEN)
Duplicates function of gREEn key for Text
TV
o
(yELLOw)
Duplicates function of yEllow key for Text
TV
b
(BLUE)
Duplicates function of BluE key for Text
TV