Pioneer SX-20-K - Manual (Page 5)

English
Français
Italiano
Español
Nederlands
Deutsch
5
En
Playback
STEREO RECEIVER
VOLUME
TUNE / PRESET MEMORY
STANDBY
A SPEAKERS B PHONES
TONE BALANCE
SX-20
STANDBY ON
/I STANDBY/ON STANDBY
iPod/USB
5V 2.1A
PURE AUDIO Hi-Bit 32 FUNCTION 
 

NETWORK AUDIO PLAYER N-50
SACD/CD NETWORK PHONO RECORDER
A C B D
1
Turn on the power of the playback component.
2
Turn power ON to the unit. ( A )
3
Select the source you want to playback. ( B )
Select the playback component.
4
Start playback of the component you selected in step 1.
5
Adjust playback volume with VOLUME control. ( C )
6
Adjust the tone to your preference using the TONE (BASS and
TREBLE) controls. (
D )
7
Select a surround mode you want. ( E )
Making an audio recording
You can make an audio recording from any audio source connected to the
receiver.
•The sound volume and tone settings made on this unit will not be
reflected in the audio output.
STEREO RECEIVER
VOLUME
TUNE / PRESET MEMORY
STANDBY
A SPEAKERS B PHONES
TONE BALANCE
SX-20
STANDBY ON
/I STANDBY/ON STANDBY
iPod/USB
5V 2.1A
PURE AUDIO Hi-Bit 32 FUNCTION 
 
 NETWORK AUDIO PLAYER N-50
SACD/CD NETWORK PHONO
RECORDER B
1
Select the source you want to record. ( B )
2
Start recording, then start playback of the source component.
© 2012 PIONEER CORPORATION.
All rights reserved.
Operation (continued)
Turntable
SACD/CD player
Network audio player
CD recorder or
Cassette deck
Listening to the radio
Use the “ F ” buttons to listening to the FM/AM radio.
1
Press FM/AM repeatedly to select the band (FM or AM).
2
Press T/P MODE to change to tuning mode.
PRESET indicator goes off.
3
Press  to tune to a station.
•Press and hold  for about a second. The receiver will start
searching for the next station.
When FM stereo broadcasts are poor because of weak broadcast signals,
press FM MODE to select the FM MONO mode to reduce the noise.
Saving station presets
If you often listen to a particular radio station, it’s convenient to have the
receiver store the frequency for easy recall whenever you want to listen to
that station.
1
Press MEM while receiving a signal from the station you want to
store.
The display shows PRESET, then a blinking MEM and station preset.
2
Press  to select the station preset you want, then press MEM.
The preset number stop blinking and the receiver stores the station.
Listening to station presets
You will need to have some presets stored to do this.
1
Press T/P MODE to change to preset mode.
PRESET indicator lights up.
2
Press to select the station preset you want.
To enjoy the many functions of the unit
to the fullest extent
Load the CD-ROM into your computer and download the PDF
manual from the menu screen to read.
Functions
•Listening to RDS broadcasts
 page 10
•Adjusting the sound volume balance
 page 11
•Using Tone Direct
 page 11
Troubleshooting
 page 13
Turntable
SACD/CD player
Network audio player
CD recorder or
Cassette deck
The front panel display does not appear.
The front panel display will not appear when the Tone Direct mode is
ON, or when the DIMMER is set to OFF.
If you not wish for the display to disappear, use TONE DIRECT button or
DIMMER
button to change the setting.
SX-20_YXE8_book.indb 5 SX-20_YXE8_book.indb 5 2012/08/03 9:33:40 2012/08/03 9:33:40