Pioneer VSX-424-K - Manual (Page 38)

Additional information 7 7
38
4
37
6
 Can’t operate the remote control.
 Replace the batteries ( page 9 ).
 Operate within 7 m, 30º of the remote sensor ( page 9 ).
 Remove the obstacle or operate from another position.
 Avoid exposing the remote sensor on the front panel to direct
light.
 Press the remote control’s button and switch to
receiver control mode.
 The display is dark.
 Press DIMMER on the remote control repeatedly to return to
the default.
 During ECO mode, the brightness switches between 2 levels. If
the dimmest level is selected, DIMMER will be shown on the
display. (Mode other than ECO: 4 levels, ECO mode: 2 levels)
 The receiver doesn’t recognize iPod touch/iPhone.
 Try the following.
1. Simultaneously keep pressing the sleep button and home
button on the iPod touch or iPhone for over 10 seconds to
restart.
2. Turn on the receiver.
3. Connect the iPod touch/iPhone to the receiver.
 Display flashes and cannot be operated.
 Depending on the input signal or listening mode, there may be
functions that cannot be selected.
HDMI
 No picture or sound.
 If the problem still persists when connecting your HDMI
component directly to your monitor, please consult the
component or monitor manual or contact the manufacturer for
support.
 No picture.
 Video signals that are input from the analog video terminal will
not output from the HDMI terminal. Signals that are input from
the HDMI terminal will not output from the analog video
terminal. Be consistent with the type of cable between input
and output.
 Depending in the output settings of the source component, it
may be outputting a video format that can’t be displayed.
Change the output settings of the source, or connect using the
composite video jacks.
 This receiver is HDCP-compatible. Check that the components
you are connecting are also HDCP-compatible. If they are not,
please connect them using the composite video jacks.
 Depending on the connected source component, it’s possible
that it will not work with this receiver (even if it is HDCP-
compatible). In this case, connect using the composite video
jacks between source and receiver.
 If video images do not appear on your TV, try adjusting the
resolution, Deep Color or other setting for your component.
 To output signals in Deep Color, use an HDMI cable (High
Speed HDMI
®/ ™ Cable) to connect this receiver to a
component or TV with the Deep Color feature.
 The OSD screen (Home Menu, etc.) isn’t displayed.
 The OSD will not appear if you have connected using the HDMI
output to your TV. Use composite connections when setting up
the system.
 No sound, or sound suddenly ceases.
 Check that the HDMI setting is set to AMP ( page 31 ).
 If the component is a DVI device, use a separate connection for
the audio.
 HDMI format digital audio transmissions require a longer time
to be recognized. Due to this, interruption in the audio may
occur when switching between audio formats or beginning
playback.
 Turning on/off the device connected to this unit’s HDMI OUT
terminal during playback, or disconnecting/connecting the
HDMI cable during playback, may cause noise or interrupted
audio.
Important information regarding the HDMI
connection
There are cases where you may not be able to route HDMI
signals through this receiver (this depends on the HDMI
equipped component you are connecting-check with the
manufacturer for HDMI compatibility information).
If you aren’t receiving HDMI signals properly through this
receiver (from your component), please try the following
configuration when connecting up.
Configuration
Connect your HDMI-equipped component directly to the
display using an HDMI cable. Then use the most convenient
connection (digital is recommended) for sending audio to the
receiver. See the operating instructions for more on audio
connections. Set the display volume to minimum when using
this configuration.
Note
• Depending on the component, audio output may be limited
to the number of channels available from the connected
display unit (for example audio output is reduced to 2
channels for a monitor with stereo audio limitations).
• If you want to switch the input source, you’ll have to switch
functions on both the receiver and your display unit.
• Since the sound is muted on the display when using the
HDMI connection, you must adjust the volume on the
display every time you switch input sources.
iPod messages
 ‘iPod/USB Error 1 (I/U ERR1)’,
‘iPod/USB Error 3 (I/U ERR3)’
 Switch off the receiver and reconnect the iPod to the receiver. If
this doesn’t seem to work, try resetting your iPod.
 ‘iPod/USB Error 2 (I/U ERR2)’
 Switch off the receiver and reconnect the iPod to the receiver. If
this doesn’t seem to work, try resetting your iPod.
 An iPod not supported by this receiver is connected. Connect
the iPod supported by this receiver ( page 24 ).
 ‘No Track’
 When there are no tracks in the category selected on the iPod.
Select a different category.
USB messages
 ‘iPod/USB Error 1 (I/U ERR1)’
 There is a problem with the signal path from the USB to the
receiver. Switch off the receiver and reconnect the USB to the
receiver.
 ‘iPod/USB Error 3 (I/U ERR3)’
 When there is no response from the USB. Switch off the
receiver and reconnect the USB to the receiver.
 ‘iPod/USB Error 4 (I/U ERR4)’
 The power requirements of the USB device are too high for this
receiver. Switch off the receiver and reconnect the USB to the
receiver.
RECEIVER